04 Saab 9.3 Alarm/Remote Start Wiring

any one have this info thanks doing  remote start and keyless

DIRECTWIRE™ WIRING INFORMATION - SAAB / 9-3 / 2004 / Remote Start

[PRINT THIS PAGE]

12volts      RED / white       +       ignition harness
Starter      brn/wht (NOT for remote start)      -       ECM, driver side connector, pin 58
Notes: The ECM is on the front passenger side of the engine.
Second Starter                 
Ignition      RED / blue       +       ignition harness
Second Ignition                 
Third Ignition                 
Accessory      blue       +       ignition harness
Second Accessory                 
Keysense      brown       +       ignition harness
Power Lock      green (4D), yellow (CV)       -       central lock switch in driver door
Notes: Lock and unlock are negative trigger thru resistors. The resistor values are not know at this time. Cut the wire and meter the switch side while pressing the central lock switch on the door.
Power Unlock      same wire as power lock            
Lock Motor      black or blue/red       5wi      driver door module in door
Unlock Motor      black or RED / blue       5wi      driver door module in door
Parking Lights+      use parking lights (-) wire            
Notes: Each light is controlled separately by the underhood and rear electrical centers.
Parking Lights-      BROWN / yellow       -       headlight switch or BCM, pin A29
Notes: The BCM is part of the fuse box under the driver side dash.
Hazards      BROWN / white       -       hazard switch or BCM, pin B61
Notes: The BCM is part of the fuse box under the driver side dash.
Turn Signal(L)      use hazards wire            
Notes: Each light is controlled separately by the underhood and rear electrical centers.
Turn Signal(R)      use hazards wire            
Reverse Light      black, red, blue, or brown       +       reverse light in trunk
Door Trigger      see notes       -       each door harness or BCM
Notes: The LF door is green to gray in pin A12. The RF door is green to ORANGE / blue in pin A11. The LR door is purple to BROWN / orange in pin A10. The RR door is purple to white in pin A9. Use all four wires and diode isolate each.

The BCM is part of the fuse box under the driver side dash.
Dome Supervision      blue/white       -       driver kick or BCM, pin A18
Notes: The BCM is part of the fuse box under the driver side dash.
Trunk/Hatch Pin      purple       -       driver kick or BCM, pin A32
Notes: The BCM is part of the fuse box under the driver side dash.
Hood Pin      yellow/blue to GREEN/ gray       -       pin switch or BCM, pin B60
Notes: The BCM is part of the fuse box under the driver side dash.
Trunk/Hatch Release      GREEN / WHITE to BROWN / red       -       driver kick or BCM, pin B58
Notes: The BCM is part of the fuse box under the driver side dash.

Meter this wire while opening the trunk with the rear trunk lid handle.
Power Sliding Door      N/A            
Factory Alarm Arm      factory remote only            
Factory Alarm Disarm      factory remote only            
Disarm No Unlock      with ignition and transponder            
Tachometer      NOT red, RED / yellow, or black       ac       any ignition coil or fuel injector
Wait to start      N/A            
Brake Wire      RED / green       +       brake pedal switch
Parking Brake      ORANGE / blue to ORANGE / white       -       parking brake switch or BCM, pin B55
Notes: The BCM is part of the fuse box under the driver side dash.
Horn Trigger      blue/white       -       Column Integration Module
Notes: The Column Integration Module is in the steering column.

The horn trigger is also brown (+) at the horn behind the front grille.
Memory Seat 1      WHITE/ red (4D), RED / gray (CV)       +       memory switch on driver seat
Memory Seat 2      PURPLE / wht (4D), gray/wht (CV)      +       memory switch on driver seat
Memory Seat 3      GREEN/ pur (4D), gray/blue (CV)      +       memory switch on driver seat
Interface Module:      Category:
Immobilizer Bypass      Required:
Yes      Type:
Transponder
Part #: 556UW
Alternate Part1 #: DesignTech 20402
Alternate Part2 #: DesignTech 29402
Notes:
Smart Starter Kill Relays: Not Available


warning      
This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.
Directed Electronics assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this

-------------
gcorrea

Just be prepared, I'm not sure what kind of saab I did earlier in the year but I couldn't get it to work, so good luck

thanks guys for the info but what about the starter wire they say not to use it .thanks