2003 Chrysler Sebring sedan wiring

DIRECTWIRE™ WIRING INFORMATION - CHRYSLER / SEBRING SEDAN / 2003 / Remote Start


12volts pink/black & red   +   ignition harness
Starter yellow   +   ignition harness
Second Starter N/A       
Ignition blue   +   ignition harness
Second Ignition GREEN/ red (20 awg)   +   ignition harness
Third Ignition          
Accessory BLACK/ orange   +   ignition harness
Second Accessory BLACK/ white   +   ignition harness
Keysense          
Power Lock WHITE/ green   +   conn. C4, pin 15 @ BCM
Notes: Lock requires a positive trigger thru a 1800 ohm resistor. Unlock requires a positive trigger thru a 750 ohm resistor. MUST use relays.

The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector C4 is a 26 pin plug on the bottom edge of the BCM.

Can also use Directed 457C or 456L interface modules.
Power Unlock same wire as power lock       
Lock Motor ORANGE / black   5wi conn. C4, pin 9 @ BCM
Notes: The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector C4 is a 26 pin plug on the bottom edge of the BCM.
Unlock Motor blue/white   5wi conn. C4, pin 13 @ BCM
Notes: The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector C4 is a 26 pin plug on the bottom edge of the BCM.
Parking Lights+ BLACK / YELLOW   +   headlight switch or DKP
Parking Lights-          
Hazards          
Turn Signal(L)          
Turn Signal(R)          
Reverse Light          
Door Trigger     -   conn. C4 @ BCM
Notes: The driver door trigger is tan in pin 5, the front passenger door is tan/red in pin 6, the left rear door is tan/orange in pin 7, and the right rear door is tan / YELLOW in pin 8. Use all four wires and diode isolate each.

The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector C4 is a 26 pin plug on the bottom edge of the BCM.
Dome Supervision use door trigger       
Trunk/Hatch Pin tan/black   -   conn. C4, pin 18 @ BCM
Notes: The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector C4 is a 26 pin plug on the bottom edge of the BCM.
Hood Pin          
Trunk/Hatch Release BLACK/ white   5wi conn. C4, pin 1 @ BCM
Notes: The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector C4 is a 26 pin plug on the bottom edge of the BCM.

The trunk release switch wire is BLACK/ white (-) at the switch or at the BCM, conn. 2, pin 3.
Power Sliding Door N/A       
Factory Alarm Arm lt. GREEN/ orange   +   conn. C4, pin 4 @ BCM
Notes: Arm requires a positive trigger thru a 1800 ohm resistor. Disarm requires a positive trigger thru a 750 ohm resistor. MUST use relays.

The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector C4 is a 26 pin plug on the bottom edge of the BCM.

Can also use Directed 457C or 456L interface modules.
Factory Alarm Disarm same wire as alarm arm       
Disarm No Unlock see factory alarm disarm       
Tachometer NOT GREEN/ lt. green   ac   any ign. coil or fuel injector
Wait to start N/A       
Brake Wire WHITE/ tan   +   brake pedal switch
Parking Brake          
Horn Trigger BLACK/ red   -   steering column
Memory Seat 1          
Memory Seat 2          
Memory Seat 3          
Interface Module: Category:
Immobilizer Bypass Required:
Yes Type:
Sentry Key
Part #: 555CW
Alternate Part1 #: 556UW
Alternate Part2 #: DesignTech 20402
Alternate Part3 #: DesignTech 29402
Notes: Only vehicles with gray keys have the immobilizer.
Interface Module: Category:
Door Lock Interface Required:
Yes Type:
Data Bus
Part #: 457CW
Alternate Part1 #: 456LW
Notes:
Smart Starter Kill Relays: Not Available



      
This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.
Directed Electronics assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information.





-------------
Be careful whose advice you buy, but be patient with those who supply it.

Thanks!