09 Accord, How to Create a Factory Rearm/Disarm?
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=140987
Printed Date: May 03, 2024 at 10:05 AM
Topic: 09 Accord, How to Create a Factory Rearm/Disarm?
Posted By: kulblue
Subject: 09 Accord, How to Create a Factory Rearm/Disarm?
Date Posted: March 08, 2016 at 6:07 PM
HI,
I have Honda Accord 2009 Coupe EX-L. I have a Issue About the Remote Start on my Cardot 1100an Alarm Remote Start (China Brand). The Alarm System Dont have the Factory Rearm/Disarm and Ground-While-Armed. Every time I press remote Start the Factory Alarm on/triggered. and I used DEI 556U Universal Immobilizer Bypass.
Any chance to add or create a Factory Rearm/Disarm? for the Alarm System?
This is the Diagram of Cardot 1100an
Replies:
Posted By: kulblue
Date Posted: March 11, 2016 at 5:59 PM
Someone?
Posted By: the12volt
Date Posted: March 11, 2016 at 6:48 PM
The 2009 Accord factory alarm arms and disarms with lock and unlock.
https://www.the12volt.com/installbay/forum_posts.asp?tid=117976#575520------------- the12volt • Support the12volt.com
Posted By: kulblue
Date Posted: March 11, 2016 at 8:27 PM
Im looking for add-on for Alarm System
The Alarm system dont had the Factory rearm and disarm output.
Posted By: the12volt
Date Posted: March 11, 2016 at 8:56 PM
No add-on needed. When you use your door lock/unlock outputs from your Cardot unit to lock/unlock the doors, the factory alarm will arm/disarm. ------------- the12volt • Support the12volt.com
Posted By: kulblue
Date Posted: March 11, 2016 at 11:59 PM
If I remote started, the alarm goes on/triggered. How I can disarm factory?
Posted By: kulblue
Date Posted: March 21, 2016 at 12:05 AM
Someone? Pls!.. Help.
Thanks.
Posted By: the12volt
Date Posted: March 21, 2016 at 10:54 AM
If you don't want to unlock the vehicle before you remote start the vehicle, you can try using two relays on the ignition output of your remote start. One to supply 12V+ to the vehicle's ignition wire and the other to provide ground to the vehicle's key sense wire. However, if it still triggers the factory alarm when you remote start the vehicle, then you can try supplying ground to the key sense wire from the "ground while armed" output you have from the relay setup I created for you in your other thread.
KEY SENSE Pink Ignition switch harness in white plug -
------------- the12volt • Support the12volt.com
Posted By: kulblue
Date Posted: March 21, 2016 at 9:40 PM
WORKS GREAT!!!! Thanks again @the12volt
Key Sense white ignition switch harness BTW. Anyway Thanks!
Posted By: the12volt
Date Posted: March 21, 2016 at 10:10 PM
You're welcome.
One reference I have shows pink, hence always using a meter to verify any wiring information before making any connections. ------------- the12volt • Support the12volt.com
Posted By: kulblue
Date Posted: March 21, 2016 at 10:18 PM
Oh ok.. How to check the key sense? Like -neg. Ground? Sorry noobie.
Posted By: the12volt
Date Posted: March 21, 2016 at 10:23 PM
On your vehicle, yes, the key sense wire will show ground when the key is in the ignition. Thankfully, you have it working, so all is good. ------------- the12volt • Support the12volt.com
Posted By: kulblue
Date Posted: March 22, 2016 at 12:55 AM
O I C.... Yup works great. Thanks again..
|