2003 Sunfire alarm wiring
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=74822
Printed Date: May 04, 2025 at 2:48 AM
Topic: 2003 Sunfire alarm wiring
Posted By: newbie99
Subject: 2003 Sunfire alarm wiring
Date Posted: March 20, 2006 at 7:36 PM
this is the manual ive got and ive never installed a alarm at all before but id like to try i also have a diagram of my car now im not sure on where some of the wires connect to i have a 2003 sunfire manual transmition
Replies:
Posted By: Twelvoltz
Date Posted: March 20, 2006 at 7:38 PM
Not really sure what you are asking for here. Maybe expand on the post with some more detail.
Posted By: newbie99
Date Posted: March 20, 2006 at 7:44 PM
ok id like to try to install this alarm myself but on the diagram im not to sure on what wire conects to what like the alarm out put wire (orange) factory disarm (purple and black) bypass out put (purple) option 1 out put (grey and black) option 1 input trigger (green and black) and also i need to install a passlock bypass
Posted By: xscash
Date Posted: March 20, 2006 at 7:45 PM
here you go....good luck....XS PONTIAC |
| MODEL | YEAR(S) | | SUNFIRE | 2000 -2003 |
| KEY | T-HARNESS | IMMOBILIZER | | N/A | GM-7 | GM's PASSLOCK 2 ANTI-THEFT System, Requires 791 Bypass Module |
| PART | COLOR | LOCATION | DIAGRAM | | 12 VOLT CONSTANT | RED (+) | IGNITON SWITCH HARNESS | | | STARTER | YELLOW (+) | IGNITION SWITCH HARNESS | | | STARTER 2 | N/A | | | | IGNITION 1 | PINK (+) | IGNITION SWITCH HARNESS | | | IGNITION 2 | N/A | | | | IGNITION 3 | N/A | | | | ACCESSORY /HEATER BLOWER 1 | ORANGE (+) | IGNITION SWITCH HARNESS | | | ACCESSORY /HEATER BLOWER 2 | N/A | | | | KEYSENSE | N/A | | | | PARKING LIGHTS ( - ) | N/A | | | | PARKING LIGHTS ( + ) | BROWN (+) | IN DRIVERS KICK PANEL | | | POWER LOCK | LIGHT BLUE (TYPE C) See NOTE *1 | IN EITHER KICK PANEL | | | POWER UNLOCK | WHITE (TYPE C) See NOTE *1 | IN EITHER KICK PANEL | | | LOCK MOTOR WIRE | GRAY (+) | IN DRIVERS DOOR HARNESS | | | DOOR TRIGGER | See NOTE *2 | IN DRIVERS KICK PANEL and PASSENGER KICK PANEL | 14301_SUNFIRE_(-) NEGATIVE DOOR PIN ISOLATION CIRCUIT.pdf | | DOMELIGHT SUPERVISION | GREEN/ BLACK (-) | IN DRIVERS KICK PANEL | | | TRUNK RELEASE | BLACK/ WHITE (+) | @ BCM, See NOTE *3 | | | SLIDING POWER DOOR | N/A | | | | HORN | BLACK (-) | @ STEERING COLUMN HARNESS | | | TACH | PURPLE / WHITE | IN MAIN ENGINE HARNESS | | | WAIT TO START LIGHT | N/A | | | | BRAKE | WHITE (+) | @ SWITCH ABOVE BRAKE PEDAL | | | FACTORY ALARM DISARM | N/A | | | | ANTI-THEFT | YELLOW (+) and BLACK (-) and WHITE (Not Used) | GM's PASSLOCK 2 System, wires are under the Steering Column cover, at the Bottom of the Ignition Switch Tumbler in a BLACK or DARK GRAY Plug | |
| NOTES | NOTE *1 if vehicle is WITHOUT Factory Keyless entry it is a TYPE C Door Locking system and MUST be tested from the PASSENGER SWITCH, if vehicle has Factory keyless Entry it is a TYPE A Door Locking System.
NOTE *2 this vehicle has a GREEN/ BLACK (-) for the DRIVERS DOOR in the drivers kick panel and a LIGHT BLUE (-) for the PASSENGER DOOR(S) in the passenger kick panel. When connecting to an Alarm system, use both wires and DIODE ISOLATE. See DIAGRAM
NOTE *3 the BCM is located to the LEFT of the STEERING COLUMN, above the DRIVERS KICK PANEL |
Posted By: newbie99
Date Posted: March 20, 2006 at 7:53 PM
ok ive got this diagram now where would i hook the wires from the alarm to i know in a compleate newbie im sorry. here is the manual for the alarm starter on page 45 or 46 the manual is located at https://caralarm.net/new_eng/manual.htm
Posted By: newbie99
Date Posted: March 20, 2006 at 8:12 PM
Posted By: newbie99
Date Posted: March 20, 2006 at 8:44 PM
im sorry i did a mistake there i copyed an pasted in notpad and its still like that im sorry
Posted By: Twelvoltz
Date Posted: March 20, 2006 at 9:04 PM
newbie99 wrote:
ok id like to try to install this alarm myself but on the diagram im not to sure on what wire conects to what like the alarm out put wire (orange) factory disarm (purple and black) bypass out put (purple) option 1 out put (grey and black) option 1 input trigger (green and black) and also i need to install a passlock bypass
Orange...not sure what it does from your description
PURPLE / Black...not needed because you do not have a factory alarm to disarm
purple...bypass output, needed to activate the passlock bypass
Grey/Black...option 1 output, probably a negative output for trunk release, you would use this with a relay to open your trunk (if you have a power trunk release from the factory)
GREEN/ Black...option 1 input trigger, I would think that since this is a 2-way alarm it would trigger an icon on the display showing this 'zone' is what is setting off your alarm, hood pin input maybe?
The 8500S From what brand? It looks the same as Scytek's 6000. Is this the same?
Posted By: the12volt
Date Posted: March 20, 2006 at 9:54 PM
newbie99 wrote:
im sorry i did a mistake there i copyed an pasted in notpad and its still like that im sorry
If you wrote your text in Notepad, then copied from Notepad into your post, that will never happen. The only way you can come close to that happening is if you viewed and copied the source code of the HTML document you created in Word, then copied that source code from that text document and pasted it into your post, but then it would have displayed as HTML coding prior to you posting. It will never happen if you copy the text you wrote in Word, paste it into Notepad, then copy from Notepad and paste it into your post. Please take a moment, as I asked you to do earlier, to read all of our forums rules before you make another post. -------------  the12volt • Support the12volt.com
Posted By: newbie99
Date Posted: March 20, 2006 at 9:56 PM
the link i posted is my alarm almost the same as the 6000 yes now for the wiring pin 5 orange armed output connects where and pin 12 yellow generator + input conects where pin 11 purple bypass output connects to the passlock pin 13 blue is the trunk - input
Posted By: newbie99
Date Posted: March 20, 2006 at 10:08 PM
12 VOLT CONSTANT RED (+) IGNITON SWITCH HARNESS = (pin 1) on 6 pin starter harness STARTER YELLOW (+) IGNITION SWITCH HARNESS = (pin 2) on 6 pin starter harness STARTER 2 N/A
IGNITION 1 PINK (+) IGNITION SWITCH HARNESS = (pin 3) on 6 pin starter harness green IGNITION 2 N/A
IGNITION 3 N/A
ACCESSORY /HEATER BLOWER 1 ORANGE (+) IGNITION SWITCH HARNESS = (pin 4) on 6 pin starter harness blue
ACCESSORY /HEATER BLOWER 2 N/A
KEYSENSE N/A
PARKING LIGHTS ( - ) N/A
PARKING LIGHTS ( + ) BROWN (+) IN DRIVERS KICK PANEL =
POWER LOCK LIGHT BLUE (TYPE C) See NOTE *1 IN EITHER KICK PANEL
POWER UNLOCK WHITE (TYPE C) See NOTE *1 IN EITHER KICK PANEL
LOCK MOTOR WIRE GRAY (+) IN DRIVERS DOOR HARNESS DOOR TRIGGER See NOTE *2 IN DRIVERS KICK PANEL and PASSENGER KICK PANEL 14301_SUNFIRE_(-) NEGATIVE DOOR PIN ISOLATION CIRCUIT.pdf
DOMELIGHT SUPERVISION GREEN/ BLACK (-) IN DRIVERS KICK PANEL = (pin 7)on 14 pin main harness grey wire
TRUNK RELEASE BLACK/ WHITE (+) @ BCM, See NOTE *3
SLIDING POWER DOOR N/A HORN BLACK (-) @ STEERING COLUMN HARNESS
TACH PURPLE / WHITE IN MAIN ENGINE HARNESS
WAIT TO START LIGHT N/A
BRAKE WHITE (+) @ SWITCH ABOVE BRAKE PEDAL = (pin 8)on 14 pin main harness red & white wire
FACTORY ALARM DISARM N/A
ANTI-THEFT YELLOW (+) and BLACK (-) and WHITE (Not Used) GM's PASSLOCK 2 System, wires are under the Steering Column cover, at the Bottom of the Ignition Switch Tumbler in a BLACK or DARK GRAY Plug
thats what i got so far
Posted By: Twelvoltz
Date Posted: March 21, 2006 at 7:05 AM
newbie99 wrote:
the link i posted is my alarm almost the same as the 6000 yes now for the wiring pin 5 orange armed output connects where and pin 12 yellow generator + input conects where pin 11 purple bypass output connects to the passlock pin 13 blue is the trunk - input
Orange = armed output, sounds like a negative trigger to activate a starter kill relay
Yellow 'Generator + input', sounds like it needs to be hooked to an ignition wire (Ignition 1 pink)
Purple bypass output = use this to activate your passlock bypass module. It will be the module's - input.
Blue Trunk input - = to black in trunk at light
Please seperate your questions into sentences, or seperate statements. Running the question together like that throws it off and confuses things.
Good Luck
Keep us posted
|