the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

wire diagram for mirrors 06 f150


Post ReplyPost New Topic
< Prev Topic Next Topic >
06f150 
Copper - Posts: 57
Copper spacespace
Joined: December 16, 2007
Location: Minnesota, United States
Posted: March 06, 2008 at 7:01 PM / IP Logged  
Does anyone have the wiring diagram for the doors/mirrors on a 06 f150?
looking for the color and functions of the wires...
Heres what I am trying to do.....
As of now I only have power mirrors (No heat, puddle, or signal).
Looking to add OEM replacement towing mirrors with heat, signal and puddle.
wanted to see if I have the wring already in my doors.
Thanks for the help!
Josh
97gss 
Copper - Posts: 235
Copper spacespace
Joined: February 12, 2004
Location: United States
Posted: March 06, 2008 at 8:27 PM / IP Logged  

You may want to contact these guys:

h ttp://www.kwmuth.com/

I did an Expedition not long ago, and they actually make the OEM stuff.

flobee4 
Silver - Posts: 585
Silver spacespace
Joined: January 02, 2004
Location: United States
Posted: March 06, 2008 at 9:11 PM / IP Logged  
I have a Ford Explorer and when my brother broke off my Driver Side mirror, I went to the Dealership and bought the OEM heated Mirror.  Originally I didn't have heated Mirrors, but I'm smart, I figured I could get the Heat working. :o)  Anyway, I plugged it in and tested it, The heat automatically worked. The car was prewired from the factory for the heat. Since its Ford offers it as OEM, maybe the car is prewired>
flobee4 
Silver - Posts: 585
Silver spacespace
Joined: January 02, 2004
Location: United States
Posted: March 06, 2008 at 10:06 PM / IP Logged  

here are directions to install aftermarket turn signal mirrors. On page 4 it shows you how to tell if your car is prewired or not.  If not, later on in the directions it shows you how to find the directional wires under the dash.

http://www.muthco.com/techsupport/pdfs/21000960.pdf

06f150 
Copper - Posts: 57
Copper spacespace
Joined: December 16, 2007
Location: Minnesota, United States
Posted: March 07, 2008 at 10:59 AM / IP Logged  
Thanks for the links....I took my drivers side door off and found that I do have the wiring for the heat and siganl but not the puddle lamp?
Any have a color for that wire and where it is to be found?
Thanks!
flobee4 
Silver - Posts: 585
Silver spacespace
Joined: January 02, 2004
Location: United States
Posted: March 07, 2008 at 4:58 PM / IP Logged  
I'm sure the puddle lamp wire is there also, how where you checking for it.  On my explorer its a postive trigger and it does come on with the interior dome light BUT not while the car is running.  If you had the ignition on maybe you missed the wire while testing. Just have the car off and turn on the dome lights at the switch.  If worst comes to worst and it is not there, you can use the domelight wire BLACK/ Blue running along the drivers side running board along side the drivers seat.  That wire is Positive, and there are more than one so check with your meter.
06f150 
Copper - Posts: 57
Copper spacespace
Joined: December 16, 2007
Location: Minnesota, United States
Posted: March 07, 2008 at 6:40 PM / IP Logged  
flobee4 wrote:
I'm sure the puddle lamp wire is there also, how where you checking for it. On my explorer its a postive trigger and it does come on with the interior dome light BUT not while the car is running. If you had the ignition on maybe you missed the wire while testing. Just have the car off and turn on the dome lights at the switch. If worst comes to worst and it is not there, you can use the domelight wire BLACK/ Blue running along the drivers side running boardalong side the drivers seat. That wire is Positive, and there are more than one so check with your meter.
I was checking them off of a wire diagram for an 05 which should be the same for 06.... but I was not actually testing them with my meter I just wanted to see if they were there.
The wires I had at the pin were
Pin location--(drivers side)
emptyempty
emptyempty
Red-    mirror movement            empty
Yellow- mirror movement            empty
yellow- mirror movement            empty
blue   -   mirror movement        empty
black -   Ground   GREEN / WHITE-signal
GREEN/ purple - heat Black- ground
I have 9 wires according to the diagram I should have 10 including the puddle lamp wire....which would be BLACK/ lt. blue...
A far as picking it up in the sill that would not be a problem as I already hooked up to that wire for my remote stater for the dome light.....so that would work at good.
One more question....for the defrost/heat wire in the mirror I do not have a defrost button now....I Believe the mirrors heat all the time, so that wire should always have current going through it right?
06f150 
Copper - Posts: 57
Copper spacespace
Joined: December 16, 2007
Location: Minnesota, United States
Posted: March 07, 2008 at 6:40 PM / IP Logged  
flobee4 wrote:
I'm sure the puddle lamp wire is there also, how where you checking for it. On my explorer its a postive trigger and it does come on with the interior dome light BUT not while the car is running. If you had the ignition on maybe you missed the wire while testing. Just have the car off and turn on the dome lights at the switch. If worst comes to worst and it is not there, you can use the domelight wire BLACK/ Blue running along the drivers side running boardalong side the drivers seat. That wire is Positive, and there are more than one so check with your meter.
I was checking them off of a wire diagram for an 05 which should be the same for 06.... but I was not actually testing them with my meter I just wanted to see if they were there.
The wires I had at the pin were
Pin location--(drivers side)
emptyempty
emptyempty
Red-    mirror movement            empty
Yellow- mirror movement            empty
yellow- mirror movement            empty
blue   -   mirror movement        empty
black -   Ground   GREEN / WHITE-signal
GREEN/ purple - heat Black- ground
I have 9 wires according to the diagram I should have 10 including the puddle lamp wire....which would be BLACK/ lt. blue...
A far as picking it up in the sill that would not be a problem as I already hooked up to that wire for my remote stater for the dome light.....so that would work at good.
One more question....for the defrost/heat wire in the mirror I do not have a defrost button now....I Believe the mirrors heat all the time, so that wire should always have current going through it right?

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer