Viper 5904 heavy wire conectoon

Remote star 10 pin heavy gauge connector H3 /1. Pink    Ignition1 input/output       H3/2 RED / white   Fuse30a ignition2 flex relay H3/3orange. Accessory out put H3/4 violet starter output H3/5 green stater input H3/6 red. Fused 30 a. Ignition1 input H3/7. Pink/white ignition 2 flex relay output H3/8pink/black flex relay input 87a H3/9 RED / black. Fuse 30a accessory /stater input Ford Explorer sport track 2005 12volt. Red Stater.     Red light Ignition 1. Lt green purple Ignition2 pink /black Acc. 1.   Grey yellow Acc. 2.    Brown I need info on how to connect viper alam 5904 used heavy wire gauge on my truck Ford Explorer 2005 sport track6300 birch lot 135

Did a 2005 Sport Trac recently.  Here is what I found :

There are four Red +12V constant 25 Amp wires at the ignition switch harness.Starter = RED / Light Blue  ( 16 gauge )Ignition = Light GREEN/ Violet  ( 12 gauge )ACC = Gray / YELLOW, Brown and Pink/Black  ( all 16 gauge )

Remote start 10 pin heavy gauge connector

H3 /1. Pink    Ignition1 input/output         Light GREEN/ VioletH3/2 RED / white   Fuse30a ignition2 flex relay       Red #1H3/3orange. Accessory out put Gray / YELLOW   H3/4 violet starter output RED / Light Blue          Cut wire - car sideH3/5 green stater input RED / Light Blue          Cut wire - ign switch sideH3/6 red. Fused 30 a. Ignition1 input      Red #2H3/7. Pink/white ignition 2 flex relay output         Brown   Set To ACCH3/8pink/black flex relay input 87a         Not UsedH3/9 RED / black. Fuse 30a accessory /stater input   Red #3

Extra 30/40 Amp SPDT Relay for ACC3

Relay Pin 85 to Viper H2/22 ORANGE (-) 200mA ACCESSORY OUTPUTRelay Pins 86 and 87 to Sport Trac Red #4 through 20 Amp fuseRelay Pin 30 to Sport Trac Pink/Black

Soldering is fun!

H2/22 Orange (-) 200ma accessory out put to relay pin86. And pin87 to acc pink and black red #4 trough pin 30 correct6300 birch lot 135

Well...

Assuming that your 30/40 Amp relay does not have internal coil quenching and you didn't want to follow standard

relay wiring conventions, you could connect the Vipers (-) ACC output to Relay Pin 86.

Assuming your removed Relay Pin 87A or completely insulated that wire, you could run the +12V supply wire to

Relay Pin 30.  ( Also assuming you are using the more common SPDT relay suggested and not a SPST relay thatdoes not have a Pin 87A )

Finally, you have nothing connected to Relay Pin 85, so it won't work.  You would have to connect a +12V constant

to Relay Pin 85 for it to output the +12V ACC signal you want on Pin 87 during a remote start.

Still like my suggestion ( which includes a fuse ) better, but it is your vehicle.

Soldering is fun!

85 h2/22orange(-) 86 ground when runing 87 acc sport track pink and black 30 12 volts red #4 Corret6300 birch lot 135

Almost...

85 h2/22orange(-)

86 12 volts red #4

87 acc sport track pink and black 30 12 volts red #4 through 20 Amp fuse

If relay has Pin 87A, ensure it is well insulated.

Soldering is fun!

86 from ignition NOT constant and a 1N4004 diode across 85 and 86, band to 86.

Thank you is work you so smart my friend6300 birch lot 135