the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

adding actuators to cable locks


Post ReplyPost New Topic
< Prev Topic Next Topic >
alarmpro 
Copper - Posts: 110
Copper spacespace
Joined: September 17, 2002
Location: United States
Posted: March 06, 2006 at 10:52 PM / IP Logged  
Does anyone know how to add actuators to cable driver doorlocks?? i tried but it would just not work!!
as soon as you cut the sleeve holding the cable, it stops working!! any help really appreciated.. thanks
05gt 
Silver - Posts: 628
Silver spacespace
Joined: October 30, 2005
Location: British Columbia, Canada
Posted: March 07, 2006 at 2:55 AM / IP Logged  
search on these forums, there has been a few topics like this, I believe there is a special part that is needed
sparkie 
Platinum - Posts: 2,061
Platinum spacespace
Joined: November 06, 2003
Location: Canada
Posted: March 08, 2006 at 6:44 PM / IP Logged  
Most installers devise a method of using the steel rods from the actuators to move a lever or mechanism of the door locks. It differs for different vehicles. You need to be creative and it helps if you have done door locks before.
sparky
swamprat323 
Gold - Posts: 1,335
Gold spacespace
Joined: September 22, 2002
Location: Florida, United States
Posted: March 08, 2006 at 7:00 PM / IP Logged  
What kind of car.
DanDan 
Copper - Posts: 125
Copper spacespace
Joined: September 25, 2002
Location: United States
Posted: March 08, 2006 at 8:39 PM / IP Logged  
My experience has been mixed. I will not put aftermarket locks in any cabled cars. I go to the dealer for that certain car and order the factory actuators. Usually when you purchase them you usually have to get the whole lockset. Some can be expensive but I have never had a problem. I have seen some creative ways of interfacing aftermarket but most will fail within a year or two or sometimes very quickly. I just did a 06 Mazda Miata and used the factory locks and although it was not cheap it will never come back for failure. I saw a civic that someone had done and was impressed with the creativity. Someone will make something sooner or later. But me, I use the factory and have had no problems.
DanDan
xscash 
Copper - Posts: 317
Copper spacespace
Joined: March 05, 2006
Location: United States
Posted: March 08, 2006 at 10:22 PM / IP Logged  

if this is a ford focus... there is a small hole @ the lock itself. you can bend the rod in a s and enter it into the hole. there is a small peice of plastic that might  bind. just use a 1/4 drill and zip it out of the way.

xs

jhgraham 
Member - Posts: 34
Member spacespace
Joined: May 20, 2005
Location: United States
Posted: March 09, 2006 at 9:05 AM / IP Logged  
Never cut the sleeve, the sleeve is an integral part of the cable, unless the sleeve/cable is secured properly. The sleeve works in tension and compression, just like a bicycle brake. You must straddle the working area with a special “C” shaped retainer that allows the cable to remain the exact length and without restricting the cable movement. When attached you may then remove the sleeve from the working area and attach the lock rod clamp. I have found no well-engineered retainers for this application. Good luck!
Knowledge is Indisputable, Opinions are Subjective.
Velocity Motors 
Moderator - Posts: 12,488
Moderator spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Fabrication. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: March 08, 2002
Location: Manitoba, Canada
Posted: March 09, 2006 at 9:16 AM / IP Logged  
First we need to know the make, model and year of the vehicle.
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
NowYaKnow 
Gold - Posts: 1,217
Gold spacespace
Joined: December 18, 2002
Posted: March 09, 2006 at 6:33 PM / IP Logged  
I would definately look for a spot to attach on the lock mechanism or up near the handle. I cut the sleeve once, and then scrambled just to get the lock working again. Sure it can be done, but I haven't seen anything great yet to hold and attach to the cable itself. Not interested in boomerangs..
Mike
ss-installer 
Silver - Posts: 444
Silver spacespace
Joined: February 27, 2005
Location: United States
Posted: March 09, 2006 at 11:09 PM / IP Logged  

secure the sleeve (wire clamps and self taps) in 2 places before cutting. then cut sleeve only enough to allow movement of the actuator rod.

did a titan a couple weeks ago. worked great.


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer