the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

pku-f1 module, 2002 Ford Focus


Post ReplyPost New Topic
< Prev Topic Next Topic >
baldbobby 
Member - Posts: 12
Member spacespace
Joined: August 05, 2006
Location: United States
Posted: January 19, 2007 at 5:36 PM / IP Logged  
Im trying to find a module that will work with my remote start feature on my 2002 ford focus..I tried the 555s module which would work the first time it was programmed and then that it..the car would not start after I tried again..I got in touch with code alarm and they told me to get this module which I now have but the wiring part is kind of confusing..it has a red for power..brown for ground output when running..which im fine with..its the other 2 connections im not sure where to hook to..it has a green wire for positive keysense input and a white wite for negative keysense input..I have a code alarm 610 system in my car..any ideas to which wires of the alame to hook these up to?? thanks
NowYaKnow 
Gold - Posts: 1,217
Gold spacespace
Joined: December 18, 2002
Posted: January 19, 2007 at 5:46 PM / IP Logged  
Don't hook them to anything just use the red and brown.
Mike
baldbobby 
Member - Posts: 12
Member spacespace
Joined: August 05, 2006
Location: United States
Posted: January 19, 2007 at 7:00 PM / IP Logged  
ok..
baldbobby 
Member - Posts: 12
Member spacespace
Joined: August 05, 2006
Location: United States
Posted: February 03, 2007 at 10:02 AM / IP Logged  
actually what I had found before about hooking the brown wire wont work on my alarm..I saw it said to hook to 3rd ignition wire on the alarm but I only have  a first and second..any ideas on where that would hook to?
NowYaKnow 
Gold - Posts: 1,217
Gold spacespace
Joined: December 18, 2002
Posted: February 03, 2007 at 10:43 AM / IP Logged  
You would hook the brown wire to the active out (-) wire (blue/black), and the red wire to constant 12 volts.
baldbobby 
Member - Posts: 12
Member spacespace
Joined: August 05, 2006
Location: United States
Posted: February 03, 2007 at 3:55 PM / IP Logged  
ok hooked everything up correctly...got the module programmed and the car remoted started the first time..now it wont remote start..light flashes like there no code being sent..any ideas?
NowYaKnow 
Gold - Posts: 1,217
Gold spacespace
Joined: December 18, 2002
Posted: February 03, 2007 at 10:08 PM / IP Logged  
Unplug the module all together and just hold it in front of the key cylinder. Does the car start and run every time that way? You may need to open up the module and see where the chip actually is so you know which end/side to hold closest to the cylinder.
Mike
baldbobby 
Member - Posts: 12
Member spacespace
Joined: August 05, 2006
Location: United States
Posted: February 04, 2007 at 2:25 AM / IP Logged  
doesnt the car start off the wires that get placed around the sensor for the chip?? it has the wires that are wrapped around the key chamber..or does the module box need to be close to the  ring also??? thanks
NowYaKnow 
Gold - Posts: 1,217
Gold spacespace
Joined: December 18, 2002
Posted: February 04, 2007 at 9:38 AM / IP Logged  
Yes it uses the ring around the cylinder, but if the chip itself is right in front of the cylinder no ring needed. If it starts every time with the box in front, either your ring isn't wrapped good enough, or your remote start isn't always powering up the module.
Mike
baldbobby 
Member - Posts: 12
Member spacespace
Joined: August 05, 2006
Location: United States
Posted: February 10, 2007 at 3:57 PM / IP Logged  

I had to reprogram the module because when I took it and placed it next to the keyring and tried to remote start it my dash light flashed and the car wouldnt start..so I reprogrammed it and it remote started the first time..then I place the module box right behind the keyring,but when I went to remote start it again,my alarm would sound...but if I moved the module away from the ring the alarm wouldnt sound,and the car wouldnt start either..im really lost on this..I had the same problem with the last module I tried..I can program and start it the first time...but then the module would lose the programming...any ideas?? thanks..


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer