the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

astroflex rs 613 will not program


Post ReplyPost New Topic
< Prev Topic Next Topic >
10secty 
Member - Posts: 2
Member spacespace
Joined: November†29, 2009
Location: Alberta, Canada
Posted: November†29, 2009 at 10:03 PM / IP Logged  

Hi guys I have a Astroflex RS-613 installed on my 2005 Chevy Colorado. It is installed with a PLJX module.

I am unable to get the system to enter into any programming modes. So I can not program the remotes etc.

I did a bunch of searching and found this info

http://www.the12volt.com/installbay/forum_posts.asp?tid=111712&KW=astrostart

But I still can not get the system to flash the lights etc showing that I have entered into the programming mode.

I have the system wired the following way.

613/PLJX RED - constant 12v underdash

613 RED / BLACK - constant 12v underdash

613 Orange (Ignition output) to PLJX  Pink(ignition) both connected to  WHITE/ Green at ignition switch.

613 Yellow (accessory output+) to WHITE/ Red at ignition switch

613 green (Parking lights Output +-) to BROWN / White -  at head light switch

613 Blue (starting output+) to Violet (start wire) on PLJX

613 Green H6 output when running - 200ma to PLJX Brown (ground when running start)

613 BLACK/ red H6 hood switch is hooked up

613 WHITE/ Green H6 (interrupt input brake)  to brake switch light blue.

613/PLJX black ground connected under dash at dash mount bolt

613 BLACK/ green (tach signal) connected at coil center wire.

PLJX  Blue(Data ecm side)  connected to WHITE/ blue at ignition swtich ecm side

PLJX Pink/White(Data key side) connected to WHITE/ blue at key side.

When you put the fuses in the unit flashes code 21 system reset. Then if you turn the key on the led turns off.

It flashes if you press the brake. If the truck is running it flashes constant.

I am wondering if the H3 Yellow (pulse start input -) needs to be hooked up?

Am I missing something? Thanks for any help with this at all!!

Nolan Nykyforuk

ppg231 
Member - Posts: 10
Member spacespace
Joined: January†16, 2008
Location: Quebec, Canada
Posted: November†30, 2009 at 12:00 PM / IP Logged  

Few details:

Make sure your PLJX wire is attached to body ground, not dash mount. The value out of the PLJX can be affected by variation on ground input.

Make sure the jumper of the PLJX is on lower 2 pins (horizontal)

Iíve sent you an updated remotes programming sheet to learn them into your RS-613. From there, you will be able to go into programming mode and change the desired settings.

10secty 
Member - Posts: 2
Member spacespace
Joined: November†29, 2009
Location: Alberta, Canada
Posted: November†30, 2009 at 1:09 PM / IP Logged  

Awesome!!! This worked like a charm!!! Thank you so much.  The programming info in the owners manual is wrong for any one else with this issue.

Great customer service from Astroflex!!!! Thanks for the help!!

Nolan Nykyforuk

golfcrazied 
Member - Posts: 4
Member spacespace
Joined: December†27, 2008
Location: Manitoba, Canada
Posted: December†05, 2010 at 1:29 AM / IP Logged  

 I also have a astro start 613 that I can't get to program. I have tried those instructions but cant get anything. anyone have any ideas? I havent had much experience with these units. I tend to use autostarts.

thanks mojo
ppg231 
Member - Posts: 10
Member spacespace
Joined: January†16, 2008
Location: Quebec, Canada
Posted: December†05, 2010 at 8:45 PM / IP Logged  

There are few things to know before trying to program an RS613.

- When the Parking light jumper is to (-), the module won't clic when parking light will flash. The LED on the module will.
- On the programming sheet, When you see a rectangular with on or off in it, it's an instruction to change the ON/OFF switch to this position; not an instruction to move the key to ON or OFF.
- To program the remotes (that are normally factory programmed) the hood need to be open. For the other programming, it doesn't matter.

Please let me know more details or feel free to contact one of our techs to help you with the programming.

PatG

golfcrazied 
Member - Posts: 4
Member spacespace
Joined: December†27, 2008
Location: Manitoba, Canada
Posted: December†06, 2010 at 6:36 PM / IP Logged  

 Thanks pat, I am still having trouble getting it to program. The led is flashing 14 times which is for the parking brake. The parking brake isnt even hooked up. IS it supposed to be? I think these units are kinda crazy to program. anyone have any ideas? thanks

thanks mojo

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Saturday, May 27, 2017 • Copyright © 1999-2017 the12volt.com Donate to the12volt.com Advertising Top of Page
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Donate to the12volt.com
Top
the12volt.com spacer
the12volt.com spacer