need odyssey 04 wire diagram

Hi,

I am looking for a Odyssey 04 Ex-L wire diagram for remote start and 2 slides door but can't find it. I will wire it with Viper 5701 remote start. If anyone have a wire diagram please share with me. I will appreciate it.

Thanks,

Thang

http://www.bulldogsecurity.com/bdnew/vehiclewiringdiagrams.asp MODEL       YEAR(S) ODYSSEY       2004 - KEY       T-HARNESS       IMMOBILIZER N/A       N/A       HONDA'S TRANSPONDER ANTI-THEFT SYSTEM, REQUIRES 791 BYPASS MODULE AND EXTRA IGNITION KEY PART       COLOR       LOCATION 12 VOLT CONSTANT       WHITE (+)       IGNITION SWITCH HARNESS STARTER       BLACK/ WHITE (+)       IGNITION SWITCH HARNESS STARTER 2       N/A       IGNITION 1       BLACK / YELLOW (+)       IGNITION SWITCH HARNESS IGNITION 2       N/A       IGNITION 3       N/A       ACCESSORY /HEATER BLOWER 1       YELLOW (+)       IGNITION SWITCH HARNESS ACCESSORY /HEATER BLOWER 2       WHITE/ BLACK (+)       IGNITION SWITCH HARNESS KEYSENSE       N/A       PARKING LIGHTS ( - )       N/A       PARKING LIGHTS ( + )       RED / BLACK (+)       @ 10 PIN PLUG DRIVER SIDE FUSEBOX POWER LOCK       BLACK/ BLUE (TYPE B) See NOTE *1       @ PASSENGER SIDE FUSEBOX, See NOTE *2 POWER UNLOCK       ORANGE (TYPE B) See NOTE *1       @ PASSENGER SIDE FUSEBOX, See NOTE *2 DOOR TRIGGER       BLACK/ WHITE (-), Requires Part #775 Relay       @ INTERIOR LIGHT SWITCH DOMELIGHT SUPERVISION       LIGHT GREEN (-), Requires Part #775 Relay       @ INTERIOR LIGHT SWITCH TRUNK RELEASE       N/A       SLIDING POWER DOOR       N/A       HORN       LIGHT GREEN/ BLUE (-)       @ STEERING COLUMN HARNESS TACH       BLUE       @ 2-PIN PLUG ABOVE BRAKE MASTER CYLINDER WAIT TO START LIGHT       N/A       BRAKE       WHITE/ BLACK (+)       @ SWITCH ABOVE BRAKE PEDAL FACTORY ALARM DISARM       See NOTE * 3       ANTI-THEFT       TRANSPONDER ANTI-THEFT SYSTEM, REQUIRES 791 BYPASS MODULE AND EXTRA IGNITION KEY       TRANSPONDER @ IGNITION SWITCH TUMBLER EXTRA INFORMATION NOTE *1 these wires can ONLY be metered or tested buy turning the key in the PASSENGER DOOR KEY CYLINDER. NOTE *2 these wires are found in a 20-pin plug on the LX models and on the EX models the wires are in a 3-pin plug. NOTE *3 the DISARM wire on the EX is a BLACK/ RED to BLUE (-) in the DRIVERS DOOR Module in the drivers door.

Thank you monty_77 Right now I am planning the wiring connection and I don't know where to connect some of wires from remote to... I hope someone could help me point out where are these connection connect to. This is my 1st time install/mod car electrical. H1/4 wht/bro flex parking light relay 87A H1/7 blue trunk (-) instant trigger input H1/8 green door (-) input H1/10 wht/ble remote start activation (-) input H1/12 orange ground when armed (-) 500mA output RS in blu/wht 2nd remote start status (-) output H2/2 light GREEN/ wht oem arm (-) 200mA output H2/6 light blue 2nd unlock (-) 200mA output H2/8 bro/blk (-) 200mA horn honk output connect to horn? H3/2 RED / wht fused 30A (contact 87 of rS flex relay) connect to #775 relay? H3/3 orange accessory output connect to yellow(+) and/or wht/blk (+)?? H3/4 violet starter output connect to blk/wht (+)? H3/5 green starter input (does it connect to wht (+)12V constant?) H3/6 red 12V(+) constant connect to wht(+)?? H3/9 RED / blk for accessory and starter relays? Thanks

thang25 wrote: H1/4 wht/bro flex parking light relay 87 H1/7 blue trunk (-) instant trigger input

You will not need ether of these wire for the remote starter

thang25 wrote: H1/8 green door (-) input

DOOR TRIGGER       BLACK/ WHITE (-)

thang25 wrote: H1/10 wht/ble remote start activation (-) input

will not us this, it used to start the remote start from something like door locks pressed three times.

thang25 wrote: H1/12 orange ground when armed (-) 500mA output

hook to something you want to turn on when doors are locked (like extra sensors)

thang25 wrote: RS in blu/wht 2nd remote start status (-)output

This will be used on the Status wire of bypass also known as GWR (Ground While Running)

thang25 wrote: H2/2 light GREEN/ wht oem arm (-) 200mA output

Will not use this wire

thang25 wrote: H2/6 light blue 2nd unlock (-) 200mA output

you will only use this if you want to set up drivers door priority and if you don't want to don't worry about it

thang25 wrote: H2/8 bro/blk (-) 200mA horn honk output connect to horn?

HORN       LIGHT GREEN/ BLUE (-)       @ STEERING COLUMN HARNESS you do not need to hook it up but it will help with programming

thang25 wrote: H3/2 RED / wht fused 30A (contact 87 of rS flex relay) connect to #775 relay?

you will want to hook this to a 12 volt source. white wire this will power the pink/white wire.

thang25 wrote: H3/3 orange accessory output connect to yellow(+) and/or wht/blk (+)??

only hook it to one of the two you can use the programable pink/white for the other one

thang25 wrote: H3/4 violet starter output connect to blk/wht (+)?

yes hook it to the blk/wht in the ignition harness

thang25 wrote: H3/5 green starter input (does it connect to wht (+)12V constant?)

no this wire can be hooked to the starter wire for anti-grind(starter kill) feature if you want to hook this up you will have to cut the starter BLACK/ white wire and hook this one to key side of wire and the violet starter output to the vehicle side of the wire.

thang25 wrote: H3/6 red 12V(+) constant connect to wht(+)??

yes will get hooked to the white 12 volt

thang25 wrote: H3/9 RED / blk for accessory and starter relays?

this will get hooked to the white 12 volt also please note that you can hook all the 12 volts to battery too

Thank for your information... I tried find a blue wire for tachometer above the brake paddle and I can't find it. Does it locate any other location? Thanks.

in a lt blue connector in the drivers kick panel (blue wire) it might be blue with silver on it not a strip

Never mind I found it. How do it find blue tachometer inside the van?

I tried to find a factory disarm alarm wire with "NOTE *3 the DISARM wire on the EX is a BLACK/ RED to BLUE (-) in the DRIVERS DOOR Module in the drivers door" Could someone tell me what is BLACK/ red to blue (-) mean??? I found blue/red wire but no BLACK/ red or blue in a driver door box.

It just means that wire changes from BLACK/ red to blue after a connector somewhere in the vehicle. Basically that wire is located on the door lock switch inside of the door, I would also check for it comming out of the door harness, probably a thin little wire.

Can someone help please... How do I change the setting from manual transmission to automatic ?? Thanks again.