false alarm non stop

Home / the12volt's Install Bay / Car Security and Convenience / false alarm non stop (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

Chaser

Member - Posts: 31

Joined: February 17, 2003

Location: Canada

Posted: May 04, 2003 at 6:25 PM / IP Logged

My alarm is falsing every half hour or so. It either shows that a door is open or the trunk. It is the two way Vadar alarm. I have put diodes on both door trigers and on the trunk trigger as well. Anyone know why its doing so and what I can do to fix it.

draasch

Gold - Posts: 2,172

Joined: February 07, 2003

Location: Florida, United States

Posted: May 04, 2003 at 8:54 PM / IP Logged

what is the yr, make, and model of car....

Good Luck

David

Ace Security

813-376-9778

Tampa

Donate to the 12volt

Velocity Motors

Moderator - Posts: 12,488

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: May 04, 2003 at 10:10 PM / IP Logged

You will need to use a relay as well as diodes to isolate the trigger wires from each other.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

Chaser

Member - Posts: 31

Joined: February 17, 2003

Location: Canada

Posted: May 13, 2003 at 2:57 PM / IP Logged

2002 mustang

draasch

Gold - Posts: 2,172

Joined: February 07, 2003

Location: Florida, United States

Posted: May 13, 2003 at 8:33 PM / IP Logged

you can try this too....

***Dome Light:Ford's G.E.M. Will Drop A Low Signal Across The Dome Light And In Most Cases Cause A False Trigger. To Eliminate This Cut the Door Pin Trigger Wires At The G.E.M. And Insert A One-Amp Diode With Band Side Faceing Doors.Make Your Isolated Connection On The Door Pin Side. The GEM (Generic Electronic Module) is to the left of the radio

Good Luck

David

Ace Security

813-376-9778

Tampa

Donate to the 12volt

Chaser

Member - Posts: 31

Joined: February 17, 2003

Location: Canada

Posted: May 15, 2003 at 3:48 PM / IP Logged

I have already installed diodes on both door trigers and on the trunk trigger. When the alarm goes off it shows as if the trunk was open, but it is not. I asummed that the diodes are ok since they were new but i am going to check just to make shure. IF ANYONE HAS ANY SUGGESTIONS PLEASE LET ME KNOW

THANKS

eckoblaze72

Member - Posts: 22

Joined: May 03, 2003

Location: United States

Posted: May 17, 2003 at 10:39 AM / IP Logged

i had something like that happen to my alarm to but mine had water dripping into it from off the serin wire.

auex

Platinum - Posts: 5,041

Joined: December 23, 2002

Location: Arizona, United States

Posted: May 17, 2003 at 2:07 PM / IP Logged

What input are you connecting the trunk pin to( door or instant negative trigger)? Also as far as diode isolating the triggers, you need two diodes per trigger, one inline with the factory wire isolating the switch from the computer and one isolating the triggers from each other to the alarm.

Certified Security Specialist

Always check info with a digital multimeter.

I promise to be good.

Tell Darwin I sent you.

I've been sick lately, sorry I won't be on much.

Jamieh560

Member - Posts: 2

Joined: May 18, 2003

Location: United States

Posted: May 18, 2003 at 8:59 PM / IP Logged

I got the same problem with my 97 explorer, what color are the wire the u cut at the GEM module too add dioides. THANKS

Chaser

Member - Posts: 31

Joined: February 17, 2003

Location: Canada

Posted: May 20, 2003 at 3:45 PM / IP Logged

The alarm i got has an input for the two door triggers and another for trunk/hood. Just a stupid question but why would you need to isolate the two door trigers from each other?

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.