the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

code alarm ca6550 remote start 98 inte


Post ReplyPost New Topic
< Prev Topic Next Topic >
joelr7309 
Copper - Posts: 97
Copper spacespace
Joined: September 23, 2002
Location: United States
Posted: November 18, 2012 at 10:45 AM / IP Logged  
I'm trying to install the remote start on a 1998 Integra Sedan.. Im done with everything and I connected everything. I'm not sure if I connected everything. can some help me what on the list is important to connect off the Code Alarm CA6550.. I'm not sure in I need a Mobilizer on this car.
Everytime I try to start the remote start but it flashes 3 time saying
Remote Start Shutdown Diagnostics
If the remote start shuts down or fails to start, the parking lights will flash one of
the patterns below indicating the shutdown input.
To manually enter diagnostics and view the last shutdown, turn the ignition ON
and press and release the button.
LED FLASHES SHUTDOWN ZONE
3 Flashes Hood Input
Brake Input
4 Flashes Remote Start Valet Mode
7 Flashes Tach not learned / Crank Average not learned
code alarm ca6550 remote start 98 inte -- posted image.
beegbie 
Copper - Posts: 341
Copper spacespace
Joined: August 17, 2002
Location: United States
Posted: November 18, 2012 at 4:37 PM / IP Logged  
First step would be to disconnect your brake and hood wires. See if it helps. Did you ground the neutral safety wire?
joelr7309 
Copper - Posts: 97
Copper spacespace
Joined: September 23, 2002
Location: United States
Posted: November 18, 2012 at 4:57 PM / IP Logged  
neutral safety wire (-) should I connect this to the Emergency E-Brake?
beegbie 
Copper - Posts: 341
Copper spacespace
Joined: August 17, 2002
Location: United States
Posted: November 18, 2012 at 6:20 PM / IP Logged  
Nope. You could, but then you would need to set the e-brake whenever using the remote start. Just ground it.
joelr7309 
Copper - Posts: 97
Copper spacespace
Joined: September 23, 2002
Location: United States
Posted: November 18, 2012 at 6:38 PM / IP Logged  
Ok I tried disconnecting the hood and brake input...
The major problem was to program the TACH while running.. I got it to where I enable the remote start then the all the lights come up ready to firing but no cranking up like I hooked up the main wires wrong.. I connect both pink/white and Pink I'm so close
Weird is when I remote start is enable I put the key in and just start the car. I can remove the key and the cars still running
smokeman1 
Platinum - Posts: 1,588
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: September 14, 2009
Location: Wisconsin, United States
Posted: November 18, 2012 at 7:00 PM / IP Logged  

Could you list what wires from the remote starter are connected to what wires on the car?  It would help us to understand what might be going on.

I don't think you need the pink/white wire for starters.

When all else fails, Read the Instructions
Support the12volt.com Make a Donation
joelr7309 
Copper - Posts: 97
Copper spacespace
Joined: September 23, 2002
Location: United States
Posted: November 18, 2012 at 8:11 PM / IP Logged  
Constant 12V+     White      Ignition Switch Harness
Starter      BLACK/ White      
Ignition      BLACK / YELLOW
Ignition 2      WHITE/ Black      
Accessory      Yellow      
Tach      Blue      Distributor
Neutral Safety Wire      GREEN / WHITE      
Brake Switch      GREEN / WHITE      
Trunk Pin      Green (-)      
Parking Lights      RED / Green      
Hood Pin      n/a      
joelr7309 
Copper - Posts: 97
Copper spacespace
Joined: September 23, 2002
Location: United States
Posted: November 18, 2012 at 8:20 PM / IP Logged  
code alarm ca6550 remote start 98 inte -- posted image.
joelr7309 
Copper - Posts: 97
Copper spacespace
Joined: September 23, 2002
Location: United States
Posted: November 18, 2012 at 8:25 PM / IP Logged  
joelr7309 wrote:
Constant 12V+     White       Ignition Switch Harness
Starter      BLACK/ WhitePurple with Relay
Ignition      BLACK / YELLOW Pink
Ignition 2      WHITE/ Black Pink/White
Accessory      Yellow   ORANGE     
Tach      Blue       Distributor       BLUE from firewall
Neutral Safety Wire      GREEN / WHITE       E-brake
Brake Switch      GREEN / WHITE  Disconnected
Trunk Pin      Green (-)    Door Trigger
Parking Lights      RED / Green  White
Hood Pin      n/a       
smokeman1 
Platinum - Posts: 1,588
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: September 14, 2009
Location: Wisconsin, United States
Posted: November 18, 2012 at 8:28 PM / IP Logged  
Is the Neutral Safety Input connected to the same GREEN / WHITE as the Brake Input?  Is this vehicle manual or  automatic? 
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Page of 4

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer