Here it is. Let me know if you have any questions:
Vehicle Information: 2011 Kia Sportage Push to Start
Alarm / Remote Start Unit: Python 1401
Bypass Module: Fortin EVO-CAN
Alarm / Remote Start / Bypass Unit Vehicle
Connection Color Description Color Polarity Location:
Python 1401
H1/1 RED / White (-)200mA trunk release output **Connect directly to bypass (6 pin connector; yellow / black)
H1/2 Red (+) 12v constant input **Connect to red / white (H3/2) between unit and fuse.
H1/3 Brown (-) Horn honk output gray or white - driver kick, white 15 pin plug; pin 6
H1/4 White / Brown light flash isolation wire **No connection
H1/5 Black (-) Chassis ground ** Connect to factory ground bolt. Scrape off any paint if needed.
H1/6 Violet (+) door trigger input **No connection
H1/7 Blue (-) factory horn input **No connection
H1/8 Green (-) door trigger input **Connect directly to bypass (10 pin connector; green)
H1/9 Black / White (-) 200mA dome light output **No connection
H1/10 White / Blue (-) remote start / turbo timer activation input **No connection
H1/11 White Parking light output blue - headlight switch, white 13 pin plug; pin 1
** Change internal parking light jumper to (-)
H1/12 Orange (-) 500mA ground when armed output **No connection
H2/1 light green / black (-) 200mA factory alarm disarm output **Connect directly to bypass (6 pin connector; purple / white)
H2/2 light green / white (-) 200mA factory alarm arm output **Connect directly to bypass (6 pin connector; purple)
H2/3 white / violet (-) 200mA Aux 1 output **No connection
H2/4 Violet / black (-) 200mA Aux 2 output **No connection
H2/5 White / black (-) 200mA Aux 3 output **No connection
H2/6 light blue (-) 200mA 2nd unlock output **No connection
H2/7 gray / black (-) diesel wait to start input **No connection
H3/1 pink ignition 1 input / output blue + back of dash fuse panel (see bypass diagram)
H3/2 Red / white (+) fused ignition 2 / flex relay input Red (40amp) + front of dash fuse panel (see bypass diagram)
H3/3 orange accessory output blue + back of dash fuse panel (see bypass diagram)
H3/4 violet starter output pink + front of dash fuse panel (see bypass diagram)
H3/5 red (+) fused ignition 1 input **Connect with red / white (H3/2) wire.
H3/6 pink / white ignition 2 / flex relay output **No connection
H3/7 pink / black flex relay input 87a key side **No connection
H3/8 red / black (+) fused accessory / starter input **Connect with red / white (H3/2) wire.
1 black / white (-) neutral safety switch input **Connect to black (H1/5) wire.
2 violet / white tachometer input white AC passenger kick, yellow 24 pin plug; pin 4
3 brown (+) brake shutdown input green / orange - blue + brake switch, white 4 pin plug, pin 1 (blue on 2.0L model)
4 gray n/o or n/c (-) hood pin switch input **Connect directly to bypass (10 pin connector; pink / black). Install hood pin if no factory pin.
5 blue / white (-) 200mA status / rear defogger output **No connection
1 pink / white (-) 200mA flex relay control output **No connection
2 orange (-) 200mA accessory output **No connection
3 violet (-) 200mA starter output **No connection
4 pink (-) 200mA ignition 1 output **No connection
5 blue (-) 200mA status output **Connect directly to bypass (6 pin connector; dark blue)
1 blue (+) lock / (-) unlock **No connection
2 empty
3 green (-) lock / (+) unlock **No connection
EVO-CAN
3 pin gray / black CAN low red CAN back of dash fuse box (see bypass diagram)_
3 pin gray / black CAN high blue CAN back of dash fuse box (see bypass diagram)_
10 pin yellow ignition **Connect directly to H3/1
10 pin green door status **Connect directly to H1/8
10 pin white trunk status **No connection
10 pin brown / white hand brake status **No connection
10 pin pink / black hood status **Connect directly to remote start input harness; pin 4 (gray). Install hood pin if no factory pin.
**If vehicle is not equipped with a factory hood pin, aftermarket pin must be added and this wire will have no connection.
10 pin light blue / black Data white / orange DATA keyless module (see bypass diagram)
6 pin purple / white unlock / disarm **Connect directly to H2/1
6 pin purple lock / arm **Connect directly to H2/2
6 pin yellow/black trunk release **Connect directly to H1/1
6 pin dark blue ground while running **Connect directly to remote start auxiliary harness; pin 5 (blue)
Edit: Not sure how you got it to format so nicely, but hopefully this isn't too confusing.
Kenny
Owner / Technician
KKD Garage LLC
Albany, NY 12205