need help with viper alarm

i need to find how to get my door lock and unlock  to work with the remote i cant seem to find the wires to hook up the green and blue wire to hook the locks up to alarm module in a 2000 impala any help would be grateful and it is a viper 300espbbaddbrad

  ITEM      |     WIRE COLOR     |POL|       WIRE LOCATION        |

|              12V|red                 |+  |ignition harness *1         ||          STARTER|yellow              |+  |ignition harness *1         ||         IGNITION|pink                |+  |ignition harness *1         ||  SECOND IGNITION|green               |+  |ignition harness *1         ||        ACCESSORY|orange              |+  |ignition harness *1         || SECOND ACCESSORY|brown *7            |+  |ignition harness *1         ||       POWER LOCK|ORANGE / black        |*2 |gray 24-pin plug @ BCM *3   ||     POWER UNLOCK|same wire as lock   |-  |gray 24-pin plug @ BCM *3   ||       LOCK MOTOR|*4                  |   |                            ||     UNLOCK MOTOR|*4                  |   |                            ||    DISARM DEFEAT|*4                  |   |                            || PARKING LIGHTS +|do NOT use          |   |                            || PARKING LIGHTS -|white *8            |   |pink 24-pin plug @ BCM *3   ||       HEADLIGHTS|yellow              |-  |gray 24-pin plug @ BCM *3   ||     DOOR TRIGGER|*5                  |-  |gray 16-pin plug @ BCM *3   || DOME SUPERVISION|use door trigger    |   |                            ||  TRUNK/HATCH PIN|RED / black           |-  |gray 24-pin plug @ BCM *3   ||TRNK/HTCH RELEASE|black               |-  |release switch              ||FCTRY ALRM DISARM|lt green            |-  |gray 16-pin plug @ BCM *3   ||       TACHOMETER|white               |   |ignition coil               ||      SPEED SENSE|green               |   |gray 16-pin plug @ BCM *3   ||       BRAKE WIRE|white               |+  |brake switch                ||     HORN TRIGGER|black *6            |-  |steering column             ||           WIPERS|                    |   |                            ||  LF WINDOW UP/DN|blue - brown        |A  |drivers window switch       ||  RF WINDOW UP/DN|lt. blu - tan       |A  |drivers door harness        ||  LR WINDOW UP/DN|green - purple      |A  |drivers door harness        ||  RR WINDOW UP/DN|lt. grn - purple    |A  |drivers door harness        || SUN RF OPN/CLOSE|                    |   |                            ||   SUN ROOF LIMIT|                    |   |                            |

Notes:

NOTE: This vehicle has the passlock II immobilizer system that, when adding a remote start, must be interfaced with. Use DEI part 555t or 555L.  *1 The ignition harness is located far right of the steering column, behind the ignition switch.  *2 Lock and unlock use the same wire. Lock requires a negative trigger with a 470 ohm resistor in-line. Unlock is negative trigger. Must use relays.    *3 The BCM is located above the brake pedal. It is a plastic box with three plugs that face the firewall.  *4 Installation of factory keyless upgrade alarm is not recommended on this vehicle because the door lock motor wires rest at approximately 7 volts.  *5 The drivers door trigger wire is blue. Blue/white will catch all other doors. Use both wires and diode isolate each.  *6 Horn can also be found at the black plug with a blue insert above the gas pedal.  *7 This wire must be powered as an accessory wire. If powered as an 2nd ignition the car will not crank.  *8 Must isolate this wire from the BCM when doing remote start to avoid 'service engine soon' light. See directfax document #1600 for wiring information.