the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

'93 Chevrolet Corsica - Remote Starter


Post ReplyPost New Topic
< Prev Topic Next Topic >
otas2004 
Member - Posts: 5
Member spacespace
Joined: December 29, 2004
Location: Canada
Posted: December 30, 2004 at 6:20 PM / IP Logged  

Im looking for wiring diagram to install a Remote Starter (ProStart) for 1993 Chev. Corsica.  I need wiring color/locations on the car.  Much appreciated! _oTas

snguyen 
Silver - Posts: 281
Silver spacespace
Joined: October 09, 2003
Location: United States
Posted: December 30, 2004 at 6:27 PM / IP Logged  

Chevrolet

Corsica

1991-1993

Remote Starter  Wiring Colors and Notes

Function

 

Vehicle  Color

Location

Start:

 

YELLOW

IGNITION SWITCH HARNESS

Ignition  #1:

 

PINK

IGNITION SWITCH HARNESS

Ignition #2:

 

ORANGE

IGNITION SWITCH HARNESS (HEAT-A/C)

Ignition  #3:

 

N/A

Accessory:

 

BROWN

IGNITION SWITCH HARNESS

Brake  Light:

 

LIGHT BLUE

SWITCH ON UPPER BRAKE PEDAL SUPPORT

Tach  Signal:

 

WHITE

AT IGNITION MODULE OR PCM *

Parking Lights:

 

BROWN

(+) AT HEADLIGHT SWITCH

Headlights:

 

YELLOW (+)

HEADLIGHT SWITCH OR BEAM SELECT SW.

Diesel  Glow Plug:

 

Clutch  Bypass Wire:

 

Notes:

 * 2.2L Engine- Tach Wire Is WHITE At Ignition Module On Driver Rear Of Engine Or At Powertrain Control Module (PCM) Located Behind Passenger Side Of Dash. 3.1L Engine Tach Wire Is WHITE At Ignition Module On Passenger Front Of Engine.

Chevrolet

Corsica

1991-1993

Alarm and Keyless  Entry Wiring Colors and Notes

Function

 

Vehicle  Color

Location

Constant  +12 Volts:

 

RED OR RED

IGNITION SWITCH HARNESS

OEM Alarm Disarm:

 

N/A

Dome  Lights/Superv:

 

WHITE

(-) PIN SWITCH OR AT COURTESY LIGHT

OEM Horn:

 

BLACK (-)

STEERING COLUMN HARNESS OR AT RELAY

Power  Lock:

 

LIGHT BLUE

AT RELAYS IN DRIVER'S KICK PANEL**

Power  Unlock:

 

BLACK

AT RELAYS IN DRIVER'S KICK PANEL**

Trunk  Release:

 

LIGHT BLUE (+)

SW. OR AT RELAY BEHIND DR. KICK

Alarm  Input Wire:

 

WHITE

(-) PIN SWITCH OR AT COURTESY LIGHT

Notes:

** See Note #202 - Positive Pulse Door Lock Diagram.
otas2004 
Member - Posts: 5
Member spacespace
Joined: December 29, 2004
Location: Canada
Posted: December 30, 2004 at 10:43 PM / IP Logged  

Thank you!!!  That was a fast response... you guys are great!!

otas2004 
Member - Posts: 5
Member spacespace
Joined: December 29, 2004
Location: Canada
Posted: January 02, 2005 at 3:37 AM / IP Logged  
I just finished instaling a ProStart 3300 on the 93 Corsica.  Car Starts fine.  Does anyone have information how to hook up the door lock/unlock feature with this unit?   Would I need any relays or not!?  Output from the prostart unit is -(ve) for lock & unlock.  Could someone show me a diagram to hook this up!  thnx.
kevindanielk 
Member - Posts: 42
Member spacespace
Joined: February 18, 2003
Location: New York, United States
Posted: January 02, 2005 at 4:27 AM / IP Logged  
You should be able to just hook up the lock and unlock wires from your prostart unit directly to the wires on the 93 corsica. It uses a type A negative door lock system. The wire colors for the 93 corsica are  lock---light blue at drivers kick panel and the unlock--- black at drivers kick panel. Good luck.
otas2004 
Member - Posts: 5
Member spacespace
Joined: December 29, 2004
Location: Canada
Posted: January 02, 2005 at 10:11 AM / IP Logged  
I tired tapping into the light blue & black wires going into the door boot but the doors were not lock or unlocking with the remote.   I thought I wired it wrong and left it like that last night.  Going to check out it again today.  thnx
Craig3708 
Copper - Posts: 155
Copper spacespace
Joined: January 30, 2004
Location: Canada
Posted: January 02, 2005 at 8:12 PM / IP Logged  

Your car has positive door locks, you can buy a device at Canadian tire that will plug into your CT-3300 and give you Pos12v lock/unlock outputs, or you can use two relays....

PIN 85 lock /  unlock (from r/s)

PiN 86&87 +12v

PIN 30 lock / unlock wire in car

     Craig..

otas2004 
Member - Posts: 5
Member spacespace
Joined: December 29, 2004
Location: Canada
Posted: January 02, 2005 at 9:35 PM / IP Logged  

I have just finished installing the keyless entry part.  Corsica has a 3 wire switch, at rest V=0, at lock & unlock v=~12. ..so it is a (+ve door lock) as you said.   Wired it with 2 relays & it is all good!  Thanks for all the help.


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Sunday, May 5, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer