’99 Olds Intrigue Remote Starter

Home / the12volt's Install Bay / Car Security and Convenience / ’99 Olds Intrigue Remote Starter (

Topic Closed)

Welcome Guest :)

Members

< Prev Page Next Page > < Prev Topic Next Topic >

Velocity Motors

Moderator - Posts: 12,488

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: January 17, 2005 at 10:30 AM / IP Logged

All the Intrigues that I have done are BROWN in a blue connector

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

tbird2340

Copper - Posts: 363

Joined: October 03, 2003

Location: Ohio, United States

Posted: January 17, 2005 at 10:42 AM / IP Logged

Jeff, thanks for the reply.. Can you tell me where you tapped in for the parking lights?

I currently have the glove box out and all the IGN wires done.. I just have to do the parking light wire and the wires below.

Could tell me where you tapped the following:

Trunk (BROWN) - It says at the switch but I really don't have access to that

Lock (RED / BLACK)

Unlock (ORANGE / BLACK)

OEM Disarm (ORANGE / BLACK)

Thanks for your time..

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: January 17, 2005 at 10:55 AM / IP Logged

Trunk (BROWN) - only found at the switch. You can pull out the wire from the bottom or remove the switch by pushing at it from the backside.

Lock (RED / BLACK)- located at the BCM in the VIOLET connector.The BCM is located on the left side of the steering column

Unlock (ORANGE / BLACK)-located at the BCM in the VIOLET connector. The BCM is located on the left side of the steering column

OEM Disarm (ORANGE / BLACK)- at the driver's kick panel in a 32 pin plug located at pin # 5

The parking light wire you can access at the BLACK connector wit the blue clip just infront of the brake pedal switch.There is a GREEN wire , then a WHITE wire then there is the BROWN parking light wire.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

tbird2340

Copper - Posts: 363

Joined: October 03, 2003

Location: Ohio, United States

Posted: January 17, 2005 at 11:26 AM / IP Logged

Jeff, your helping me out very much on this install.. I appreciate it..

The brake wire (white).. Is it just in a two wire connector (the other wire being orange)?

tbird2340

Copper - Posts: 363

Joined: October 03, 2003

Location: Ohio, United States

Posted: January 17, 2005 at 11:49 AM / IP Logged

Jeff, also... Is the lock/unlock wires in the same harness clip as the OEM (orange / black) disarm? I see no violet connector.. There are however a RED / black and orange / black wires in this harness.

Thanks

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: January 17, 2005 at 1:28 PM / IP Logged

tbird2340 wrote:

Jeff, your helping me out very much on this install.. I appreciate it..

The brake wire (white).. Is it just in a two wire connector (the other wire being orange)?

Yes, that is the correct wire. The switch is a WHITE plunge type switch with the two wires in it as you desribed.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: January 17, 2005 at 1:29 PM / IP Logged

tbird2340 wrote:

Thanks

It's not completely VIOLET, rather just to top portion of it with a BLUE clip. Test the wires to ensure that they have 12 volts on them when at rest and (-) when triggering the lock/unlock.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

tbird2340

Copper - Posts: 363

Joined: October 03, 2003

Location: Ohio, United States

Posted: January 17, 2005 at 1:36 PM / IP Logged

Are the lock / unlock wires in the same connector as the OEM disarm?

tbird2340

Copper - Posts: 363

Joined: October 03, 2003

Location: Ohio, United States

Posted: January 17, 2005 at 1:57 PM / IP Logged

The two wires I have tapped into are not the correct wires.

The RED / black I'm tapped into provides about 11.5V with nothing on and doesn't change when I press lock/unlock.

The ORANGE / black I'm tapped into doesn't provide any power with nothing on and also doesn't change when I press lock/unlock..

tbird2340

Copper - Posts: 363

Joined: October 03, 2003

Location: Ohio, United States

Posted: January 17, 2005 at 2:02 PM / IP Logged

Take that back. I have the correct lock (RED / black) wire..

Just trying to find the correct ORANGE / black wire.

There are two in the harness I am in. One (Pin 5) is supposed to be the OEM disarm. The other is the one I'm tapped into but isn't working.

Is it possible the OEM disarm Pin 5 is the actual unlock wire?

< Prev Page Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.