the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

1999 Cadillac Eldorado remote start


Post ReplyPost New Topic
< Prev Topic Next Topic >
link123 
Member - Posts: 21
Member spacespace
Joined: August 29, 2004
Location: United States
Posted: December 05, 2005 at 9:37 PM / IP Logged  

Hi,

I am planning to install a remote starter on this my vehicle, please tell me what bypass I need for this particular car.  Also direct me where I can purchase the module.

thx

mobileworks 
Copper - Posts: 136
Copper spacespace
Joined: December 16, 2004
Location: United States
Posted: December 05, 2005 at 10:22 PM / IP Logged  
secureauto 
Copper - Posts: 196
Copper spacespace
Joined: January 02, 2003
Location: California, United States
Posted: December 05, 2005 at 10:38 PM / IP Logged  
Here's a link for your car:
99 Eldorado
And here's a link for VATS bypass diagram, no need for module:
techtip 1049
ASE Certified
link123 
Member - Posts: 21
Member spacespace
Joined: August 29, 2004
Location: United States
Posted: December 07, 2005 at 12:04 AM / IP Logged  

where can I buy the 652T resistor pack?   or can I use a 555U?

secureauto 
Copper - Posts: 196
Copper spacespace
Joined: January 02, 2003
Location: California, United States
Posted: December 07, 2005 at 11:19 PM / IP Logged  
There's no need to buy the whole pack, your Cadi's key should have a small black chip looking thing on it. That's a resistor, use a Digital Multi Meter, switch to resistance or Ohm's and measure the resistor on your key. Go to your nearest Radio Shack and pick up some resistor's. You may not find the exact value of resistor at the store, but if you find one very close in value, about 5% over or under the value should be o.k. adding resistor's in line (series or parallel) is ok to come close to the value on your key.
ASE Certified
link123 
Member - Posts: 21
Member spacespace
Joined: August 29, 2004
Location: United States
Posted: December 29, 2005 at 8:54 AM / IP Logged  

I check at radio shack and they have the 1/2w carbon film resistor and 1/4w carbon film resistor,  what watt should I get?

robdog1969 
Member - Posts: 29
Member spacespace
Joined: December 29, 2005
Location: United States
Posted: December 29, 2005 at 1:46 PM / IP Logged  
1/4 w is fine if you want to all you have to do is cut  the orange ribbon wire and solder a resistor on the 2 wires comming from firewall but it defeats the vats
over 20 years of experience in the 12 volt industry

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, May 2, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer