Mazda Miata, Viper 791XV

Home / the12volt's Install Bay / Car Security and Convenience / Mazda Miata, Viper 791XV (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

speedcrazy

Member - Posts: 4

Joined: October 04, 2006

Location: United States

Posted: October 04, 2006 at 9:42 PM / IP Logged

Hi Everyone

My name is Leo, I'm new here

I have Mazda Miata with the viper 791xv alarm installed. i have noticed yesterday that when i engage the alarm, its not locking the doors for some reason. it used to do it before Mazda Miata, Viper 791XV -- posted image.

did i pressed some i shouldn't or some wire got disconnected Mazda Miata, Viper 791XV -- posted image.

is there any way to reset the system to the default setting or should i go to the alarm guy, let him take a look at it Mazda Miata, Viper 791XV -- posted image.

Best Regards

Leo

shaggy12volt

Copper - Posts: 164

Joined: July 16, 2002

Location: Ohio, United States

Posted: October 04, 2006 at 10:48 PM / IP Logged

what year is your car

The Shagmaster

1999 Chevy Suburban 15" lift sittn on 22's sets 7'5"

1992 Chevy Astro Van all Bagged out Dubbed THE SUICIDER

Installing for over 18 years Looking for empolyment NOW send PM for resum

captainzab

Silver - Posts: 606

This member has made a donation to the12volt.com. Click here for more info.

Joined: February 09, 2005

Location: United States

Posted: October 04, 2006 at 11:23 PM / IP Logged

01-05 miata

common problem is that the connection is bad at the resistor

i usually [buttend]- [resistor]- [buttend]

sometimes, the resistor wiggle alittle. not sure if this is how your installer did it.

take a look at the lock wire

Note: You Always Dont Get What You Pay For.

speedcrazy

Member - Posts: 4

Joined: October 04, 2006

Location: United States

Posted: October 04, 2006 at 11:34 PM / IP Logged

my car is 2000

and when i bought it i went to install that alarm

and they also installed the door lock thing, that locks the doors by itself.

Best Regards

Leo

captainzab

Silver - Posts: 606

Joined: February 09, 2005

Location: United States

Posted: October 04, 2006 at 11:37 PM / IP Logged

99-00 Miata

my guess is either the relay or the actuator

Note: You Always Dont Get What You Pay For.

shaggy12volt

Copper - Posts: 164

Joined: July 16, 2002

Location: Ohio, United States

Posted: October 04, 2006 at 11:46 PM / IP Logged

more than likely your resister has come disconected or loose.

if they were a good installer the should have soldered your conections and heat shrinked or tape them up a good you sould always have that resester soldered in line within the lock wire that way it wouldint come loose. if they used but conecters to conect the resister make them fix it and solder it

you must you relays with a 1000ohm resister on the lock wire they probly sold you a 451m for your keyless it could have a blown fuse also i take it it still unlocks but no lock the locking the doors by it self should be being done by the brain. oh does your car lock and unlock with the factory switches?

Power Lock	purple	-	door lock control module
Notes: Lock is negative trigger thru a 1,000 ohm resistor. Unlock is a straight negative trigger. MUST use relays. The door lock control module is under the driver side dash towards the center of the instrument cluster. Also found at the keyless control module behind the glove box, if equipped.
Power Unlock	same as power lock wire

The Shagmaster

1999 Chevy Suburban 15" lift sittn on 22's sets 7'5"

1992 Chevy Astro Van all Bagged out Dubbed THE SUICIDER

Installing for over 18 years Looking for empolyment NOW send PM for resum

speedcrazy

Member - Posts: 4

Joined: October 04, 2006

Location: United States

Posted: October 05, 2006 at 11:22 AM / IP Logged

when i lock it by myself both doors locking automaticly.....

but it was doing it even before they installed the alarm.

Best Regards

Leo

speedcrazy

Member - Posts: 4

Joined: October 04, 2006

Location: United States

Posted: October 05, 2006 at 3:38 PM / IP Logged

i went to the car got under the wheel

there was a bundle of wires going out from little black box

with a fuse i touched it a bit tight everything up

and its working now

should i look for something special in that bundel?

Best Regards

Leo

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Mazda Miata, Viper 791XV

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.