the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

ported enclosure, sq


Post ReplyPost New Topic
< Prev Topic Next Topic >
jurb 
Member - Posts: 39
Member spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: May 23, 2007
Location: United States
Posted: July 03, 2007 at 9:40 PM / IP Logged  
i am still trying to model a pair of 15" TC1000s in a ported box. i took out the back seat of my truck and will be using the whole space to build the enclosure. i have a few questions about my winisd simulations.
from winisd help:
"This graph shows gain in dB related to driver's limit efficiency n0. Which it theoretically reaches at infinite frequency. This is the basic graph, which is needed most."
what exactly does that mean? the limit efficiency is where the sub reaches maximal impedance? the second question i have is how does this relate to sq? why do most people consider a flatter curve better for sq? is this because the sub is maximally efficient throughout the response range that you desire?
the other thing that i am confused about is the tuning of a ported box, is that the resonance frequency of the enclosure? how does that factor into my design of a box? thanks for the help.
stevdart 
Platinum - Posts: 5,816
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: January 24, 2004
Location: Pennsylvania, United States
Posted: July 04, 2007 at 11:18 PM / IP Logged  

It's not unusual, when working with WinISD and following the Help files, to look to other sources for additional information.  See  http://www.lalena.com/audio/basic/terms/ .  For the info you cited re: "transfer function magnitude", look at this graph as a representation of relativity.  With the "0" red line being flat, responses below this line are lower in db while above the line higher. 

The relatation to SQ is in the peaks of the response and in the slope of the response's fall.  Some woofers will show a peak above the reference line and you will notice that the peaking diminishes as you provide more airspace.  At the same time, however, you will notice that cone excursion can quickly get out of control with the larger airspace.  You have to reach a compromise in freq response by checking all the available graphs when designing your enclosure.

For SQ you will try to reach as flat a response as you can...there are a lot of reasons.  The vehicle itself will cause peaking (cabin gain) and you don't want to add to that bandpass region unnecessarily.  +3 db shows an accoustical doubling of power to that frequency range.

The author's wording described "efficiency" and "n0" when describing this graph, but you shouldn't be concerned with driver efficiency while working with this program.  The efficiency is what it is for any given driver.  Use this graph to help you arrive at the best airspace to allow for maximum flat response while keeping cone excursion under Xmax at your specified power input.

Port tuning:  adds additional sound to the woofer by using a resonator.  You will see the results of the port by looking at the graph "Rear Port - Air Velocity".  It shows output of the port only and at what frequency.  You will notice that the resonance is at about 10 Hz higher than Fb (box tuning freq) in most cases.  For SQ I like to tune as low as possible.  Sometimes it is the case where port output is virtually nonexistant in a SQ vented box.  The venting is done because it is the best way to utilize the particular woofer...such as where using it in a sealed box limits, too much, the low end freq response. 

Build the box so that it performs well in the worst case scenario and, in return, it will reward you at all times.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer