07 mazda cx-7 alarm/radio

Home / the12volt's Install Bay / Car Security and Convenience / 07 mazda cx-7 alarm/radio (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

Z-man

Member - Posts: 12

Joined: January 09, 2003

Location: United States

Posted: November 09, 2006 at 12:00 AM / IP Logged

Just seeing if anyones got these diagrams yet( alarm/radio) and if so, could I please get any info for this veh. Thanks

Mike M2

Platinum - Posts: 2,652

Joined: June 29, 2005

Location: United States

Posted: November 09, 2006 at 6:54 AM / IP Logged

12volts	red (40A), red (40A)	+	ignition harness
Starter	gray/red	+	ignition harness
Second Starter	N/A
Ignition	GREEN/ YELLOW	+	ignition harness
Second Ignition	N/A
Third Ignition	N/A
Accessory	pink / YELLOW	+	ignition harness
Second Accessory	yellow	+	ignition harness
Keysense	RED / black or BROWN / green	+	ign harn or BCM, 24 pin plug, pin 3C
Notes: The BCM (Body Control Module) is high in the driver kick.
Power Lock	GREEN/ red to BLACK/ blue	-	dr kick or BCM, 30 pin plug, pin 5M
Notes: Lock is negative trigger thru a 1000 ohm resistor. Unlock is a straight negative trigger. MUST use relays. The BCM (Body Control Module) is high in the driver kick.
Power Unlock	same as power lock wire
Lock Motor	yellow/black	5wi	dr kick or BCM, 6 pin plug, pin 6E
Notes: The BCM (Body Control Module) is high in the driver kick.
Unlock Motor	WHITE/ red to WHITE/ black	5wi	dr kick or BCM, 6 pin plug, pin 6C
Notes: The BCM (Body Control Module) is high in the driver kick.
Parking Lights+	RED / blue	+	driver kick, harness to rear
Parking Lights-	BLACK/ red	-	headlight switch, pin L
Hazards	BLACK/ orange	-	switch or BCM, 24 pin plug, pin 3J
Notes: The BCM (Body Control Module) is high in the driver kick.
Turn Signal(L)	blue	+	dr kick or BCM, 30 pin plug, pin 5R
Notes: The BCM (Body Control Module) is high in the driver kick.
Turn Signal(R)	blue/red	+	dr kick or BCM, 30 pin plug, pin 5O
Notes: The BCM (Body Control Module) is high in the driver kick.
Reverse Light	GREEN/ orange	+	driver kick, harness to rear
Door Trigger	see notes	-	BCM, 30 pin plug
Notes: The LF door is BLACK / YELLOW in pin 5Y. The RF door is BLACK/ blue in pin 5V. The LR door is BLACK/ orange in pin 5S. The RR door is BLACK/ green in pin 5T. Use all four wires and diode isolate each. The BCM (Body Control Module) is high in the driver kick.
Dome Supervision	BLACK/ blue	-	dr kick or BCM, 6 pin plug, pin 6B
Notes: The BCM (Body Control Module) is high in the driver kick.
Trunk/Hatch Pin	BLACK/ red	-	dr kick or BCM, 30 pin plug, pin 5P
Notes: The BCM (Body Control Module) is high in the driver kick.
Hood Pin	BLACK / YELLOW	-	pin sw or BCM, 16 pin plug, pin 1A
Notes: The BCM (Body Control Module) is high in the driver kick.
Trunk/Hatch Release	N/A
Power Sliding Door	N/A
Factory Alarm Arm	BLACK/ white	-	dr kick or BCM, 30 pin plug, pin 5A
Notes: Meter this wire while turning the key in the driver door key cylinder. Arm is negative trigger thru a 1000 ohm resistor. Disarm is a straight negative trigger. MUST use relays. The BCM (Body Control Module) is high in the driver kick.
Factory Alarm Disarm	same as factory alarm arm wire
Disarm No Unlock
Tachometer	GREEN/ stripe	ac	any fuel injector
Notes: Can also go to any ignition coil and use the wire that is NOT green or BLACK/ blue.
Wait to start	N/A
Brake Wire	RED / white	+	brake pedal switch or driver kick
Parking Brake	BLACK/ red	-	switch or BCM, 16 pin plug, pin 1C
Notes: The BCM (Body Control Module) is high in the driver kick.
Horn Trigger	black	-	switch or BCM, 24 pin plug, pin 3H
Notes: The BCM (Body Control Module) is high in the driver kick.
Memory Seat 1	N/A
Memory Seat 2	N/A
Memory Seat 3	N/A

Interface Module:	Category: Immobilizer Bypass	Required: Yes	Type: Transponder
Part #: 556UW

Mike M2

Tech Manager

CS Dealer Services

Z-man

Member - Posts: 12

Joined: January 09, 2003

Location: United States

Posted: November 09, 2006 at 9:05 AM / IP Logged

Thanks mr. Mike..I'll check it out. 07 mazda cx-7 alarm/radio -- posted image.

Z-man

Member - Posts: 12

Joined: January 09, 2003

Location: United States

Posted: November 29, 2006 at 8:38 PM / IP Logged

will the 556U work for this install on the remote start. Thanks for any info you might have!

jasondavis05

Copper - Posts: 55

Joined: November 14, 2006

Location: United States

Posted: December 05, 2006 at 12:42 AM / IP Logged

Yes Mike M2 has it there at the bottom

Interface Module:	Category: Immobilizer Bypass	Required: Yes	Type: Transponder
Part #: 556UW

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

07 mazda cx-7 alarm/radio

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.