2006 Toyota Tundra DC V8 Alarm/Remote Start Wiring

Thanks for your help, in ref Note #1 diagram is there a link to the diagram?

DIRECTWIRE™ WIRING INFORMATION - TOYOTA / TUNDRA DOUBLE CAB / 2006 / Remote Start 12volts wht/blue (40A), wht/red (25A)   +   ignition harness Starter BLACK/ white   +   ignition harness Second Starter N/A        Ignition BLACK/ red   +   ignition harness Second Ignition BLACK / YELLOW   +   ignition harness Third Ignition N/A        Accessory pink   +   ignition harness Second Accessory N/A        Keysense YELLOW /GREEN   -   ign harn or BECU, black plug, pin 22 Notes: Using the status output wire from the remote start to trigger this wire will disarm the alarm without unlocking the doors. The BECU (Body ECU) is above the driver kick panel, towards the firewall. Power Lock see DirectFax document 1070        Power Unlock see power lock        Lock Motor blue/red   5wi DKP or BECU, black plug, pin 1 Notes: The BECU (Body ECU) is above the driver kick panel, towards the firewall. Unlock Motor RED / black   5wi DKP or BECU, black plug, pin 14 Notes: The BECU (Body ECU) is above the driver kick panel, towards the firewall. Parking Lights+ green   +   driver kick, harness to rear Parking Lights- green   -   switch or BECU, white plug, pin 14 Notes: The BECU (Body ECU) is above the driver kick panel, towards the firewall. Hazards GREEN/ red   -   turn signal flasher below fuse box Turn Signal(L) GREEN/ black   +   turn signal flasher below fuse box Turn Signal(R) GREEN/ YELLOW   +   turn signal flasher below fuse box Reverse Light RED / black   +   driver kick, gray 8 pin plug, pin 2 Door Trigger blue/red (ajar indicator)   -   BECU, white plug, pin 1 Notes: The BECU (Body ECU) is above the driver kick panel, towards the firewall. The individual door trigger wires are also at the BECU. The LF door is gray/red, gray plug, pin 15. The RF door is lt. GREEN/ black, black plug, pin 8. The LR door is RED / white, gray plug, pin 16. The RR door is RED / white, black plug, pin 4. Use all four wires and diode isolate each. Dome Supervision blue/black   -   ignition key cylinder illumination Notes: Also found at the BECU, gray plug, pin 8. The BECU (Body ECU) is above the driver kick panel, towards the firewall. Trunk/Hatch Pin N/A        Hood Pin blue/white   -   pin sw. or BECU, white plug, pin 5 Notes: The BECU (Body ECU) is above the driver kick panel, towards the firewall. Trunk/Hatch Release N/A        Power Sliding Door N/A        Factory Alarm Arm arms with lock        Factory Alarm Disarm disarms with unlock        Disarm No Unlock use key sense wire        Tachometer black   ac   ECM, 2nd plug from right, pin 1 Notes: The ECM (Engine Control Module) is behind the glove box. Wait to start N/A        Brake Wire WHITE/ red or GREEN / WHITE   +   brake pedal switch Parking Brake lt. GREEN/ red   -   switch or BECU, black plug, pin 3 Notes: The BECU (Body ECU) is above the driver kick panel, towards the firewall. Horn Trigger BLACK / YELLOW   -   switch or BECU, black plug, pin 21 Notes: The BECU (Body ECU) is above the driver kick panel, towards the firewall. Memory Seat 1 N/A        Memory Seat 2 N/A        Memory Seat 3 N/A        Interface Module: Category: Immobilizer Bypass Required: No Type: N/A Part #: N/A Notes: Interface Module: Category: Door Lock Interface Required: No Type: Data Bus Part #: IM-Toyota-2 Notes: Smart Starter Kill Relays: Not Available        This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter. Directed Electronics assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information. 37Z_1070.pdfBe careful whose advice you buy, but be patient with those who supply it.

most appreciated guys!!!!  over the next day or so I will putting down what I want to do with the alarm and how I intend to do it.  Of course, I am looking to read everyones comments.

Easy truck, not many shortcuts to take. Use the supervision wire for door trigger, it catches all 4 doors. I use a coil wire instead of going to the BCM, lots easier. When wiring the 1070 document, use the WHITE/ black at the door switch for ground(the metal of the door tends to not make a solid ground going thru the hinges). No immobilizer....Mike M2

Tech Manager

CS Dealer Services

I have a new Autopage LCD 860 Alarm and here is what I am looking to do:

Remote start

Starter kill switchRemote windows up and downRemote door locksMercury switcBattery back upExtra piezo sirens inside the cabinRemote placement of the controller/cpu

A little background, I have done a couple of alarms in my days, car and residential audio.  Comments?