the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

mold makeing materials?


Post ReplyPost New Topic
< Prev Topic Next Topic >
goaheadandh8me 
Member - Posts: 13
Member spacespace
Joined: September 12, 2008
Location: Florida, United States
Posted: September 12, 2008 at 2:03 AM / IP Logged  
i was just wondering what material/materials, would work to fashion a mold with flowing curves and irregular patterns on it.  i was looking for somthing that would hold up to the resin and could be formed with common tools like belt sander, rasps, ect and not cost a fortune.  i am looking to form a mold to replace my door pockets on my door panels on my 01 accord coupe for a three way front stage component set.
josh
jayson33 
Copper - Posts: 165
Copper spacespace
Joined: June 12, 2008
Location: Indiana, United States
Posted: September 14, 2008 at 11:29 PM / IP Logged  

Find you a hobby shop get Green Floral foam it can be rough cut easly with an electric knife and then sanded

with 120 grit to shape it (green foam its used to make flower arangments) Its farily cheap

My wife thinks bagging a truck means you kick it in the truck nuts
goaheadandh8me 
Member - Posts: 13
Member spacespace
Joined: September 12, 2008
Location: Florida, United States
Posted: September 17, 2008 at 5:38 PM / IP Logged  
thanks, thats a good idea, do you know if the resin will mess up the foam?  if so, what do i cover the foam with to prevent this?
josh
jayson33 
Copper - Posts: 165
Copper spacespace
Joined: June 12, 2008
Location: Indiana, United States
Posted: September 17, 2008 at 10:41 PM / IP Logged  

You will want to foil it or something that I have used last couple time is sarin-wrap pull it tight to were it forms

to mold without any wrinkles in it. The last time I tried it pulled right out. Left a glass smooth finish on the inside NOTE: Acetone will dissolve the foam to a sticky nasty mess

My wife thinks bagging a truck means you kick it in the truck nuts
top_gear_center 
Member - Posts: 1
Member spacespace
Joined: April 27, 2009
Location: Egypt
Posted: April 27, 2009 at 4:23 PM / IP Logged  

I did alot of  fiberglass fabrications and i used different kinds of materials like (foam - mdf - wood - fiber putty - strong paper - skin steel - aluminum ) to made moulds and have the best shape from the first time .

but you should know that there is no limits for materials or means that you can use to fabricate the fiberglass , I deal with fiber as a challenge , and i advice all do the same .

your friend ahmed


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer