the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Increase in sound with more watts?


Post ReplyPost New Topic
< Prev Topic Next Topic >
ford_lightning 
Member - Posts: 3
Member spacespace
Joined: September 17, 2004
Location: Albania
Posted: December 05, 2005 at 3:45 PM / IP Logged  
Hello everyone,
Right now I have a Kicker L5 in a wedge truck box being pushed by a kicker zr240 amp. Its not as loud as I expected.
The amp is:
RMS Power at 4 Ohms       60 W x 2
RMS Power at 2 Ohms      120 W x 2
The problem is Im not sure if the L5 is the dual 4 ohm or dual 2 ohm. It just has a red and black wire coming from the back.
Any suggestions? I have the amp bridged.
stevdart 
Platinum - Posts: 5,816
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: January 24, 2004
Location: Pennsylvania, United States
Posted: December 05, 2005 at 4:21 PM / IP Logged  

A bad marriage.  Divorce is imminent. 

The L5 is a SPL sub that likes a lot of power and a big enclosure.  You have neither of these, so you should consider a high efficiency subwoofer that doesn't mind a small box.  And you should also consider using that amp to power a set of speakers and buying a more powerful mono amp for subwoofer use.

Find out what amp you will use first, then pick a sub based on the above criteria PLUS its impedance (which means you'll have to find out what the coil(s) is rated at).

Build the box so that it performs well in the worst case scenario and, in return, it will reward you at all times.
forbidden 
Platinum - Posts: 5,353
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spacespace
Joined: November 01, 2003
Location: Alberta, Canada
Posted: December 05, 2005 at 4:22 PM / IP Logged  
Take the sub out of the box and let us know the proper model # of it and how it is wired. I ask this as I am presuming that you do not have a meter to measure the dcr of the speaker.
Top Secret, I can tell you but then my wife will kill me.
ma1302 
Member - Posts: 5
Member spacespace
Joined: November 22, 2005
Posted: December 07, 2005 at 8:02 AM / IP Logged  
I think you should get a vented single box for the sub , that way the sub will act if it was in a larger enclosure. Being behind the seat of the truck it's limited to how much air the sub can move in that tight space. Your results should be better if you try this. 
DYohn 
Moderator - Posts: 10,741
Moderator spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spacespace
Joined: April 22, 2003
Location: Arizona, United States
Posted: December 07, 2005 at 4:04 PM / IP Logged  

ma1302 wrote:
I think you should get a vented single box for the sub , that way the sub will act if it was in a larger enclosure. Being behind the seat of the truck it's limited to how much air the sub can move in that tight space. Your results should be better if you try this. 

Not trying to slam you or anything but that is not correct.  A "vented" enclosure does not make a speaker act like it's in a larger enclosure.  Bass Reflex (vented or ported) enclosures simply function differently from sealed ones, with a 3-6db bump in output at the port tuning frequency and a loss of enclosure-related speaker damping below the port tuning frequency.  Vented enclosures act much differently and must be used differently (such as adding subsonic filters) from sealed enclosures.  And mounting a sub in a tight space may or may not have any effect whatsoever on output, as long as the woofer can move unimpeded to its excursion limits and the port (if used) is not blocked, the air space clearance required is very small indeed.

Support the12volt.com

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer