the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

why use domelight as door trigger?


Post ReplyPost New Topic
< Prev Topic Next Topic >
c.c.autospa 
Copper - Posts: 49
Copper spacespace
Joined: March 09, 2007
Location: Florida, United States
Posted: April 20, 2008 at 9:41 AM / IP Logged  
Im a rookie car alarm installer and although i personally dont do it, i noticed that alot of installers wire the alarms door triggers into the cars domelight switch. I was just wondering is this an installers preference or some specfic reason that it's wired that way?
cedric
i am an idiot 
Platinum - Posts: 13,693
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: April 20, 2008 at 9:56 AM / IP Logged  

This is a normal practice.  But if YOU want to be different, You could run a wire to each door pin, and have to diode isolate each wire (in a lot of cars) some cars you would not need to use the diodes.  The door pins control the domelight.  The domelight is just easier because you only have to make the one connection.

c.c.autospa 
Copper - Posts: 49
Copper spacespace
Joined: March 09, 2007
Location: Florida, United States
Posted: April 20, 2008 at 11:12 AM / IP Logged  
But what if the alarm has a wire for domelight supervision(clifford) and door triggers, would you still connect the door triggers to the car's domelight switch?
cedric
i am an idiot 
Platinum - Posts: 13,693
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: April 20, 2008 at 12:03 PM / IP Logged  

Yes.

sparkie 
Platinum - Posts: 2,061
Platinum spacespace
Joined: November 06, 2003
Location: Canada
Posted: April 20, 2008 at 7:53 PM / IP Logged  
In some vehicles you need to wire into each door pin and diode isolate them. Some factory dome light wires can be deactivated with a switch on the dome light or dash. Tapping into the dome light wire on such a vehicle wouldn't be the correct method because if the switch were in the wrong position, the alarm wouldn't respond to a open door. On some vehicles the dome lights won't come on during the day because the car senses the light level inside and won't turn them on with a door open. Some alarms won't arm properly if the dome light wire stays active for a time after closing the door. They may not monitor the dome light wire if they see it active while arming. The prefered method for all these reasons is to use each doorpin circuit. Sure the dome light wire is quicker in most cases, but if the alarm isn't installed well, it won't be a very effective system.
sparky
chriswallace187 
Gold - Posts: 1,661
Gold spacespace
Joined: March 11, 2002
Location: Pennsylvania, United States
Posted: April 21, 2008 at 12:39 AM / IP Logged  

c.c. autospa, the main impetus is the simplicity - all the alarm needs is a wire which will show ground or 12v+ when any door is opened.

It's an acceptable practice to connect the door trigger and dome supervision to the same wire. The reason is that the alarm only activates the dome supervision when it's either 

1. just been disarmed, and the ignition hasn't been turned on.
2. actively going off.

In either of those 2 cases the alarm is not really concerned whether the doors are open or not.

The dome supervision should ideally activate a relay(if the alarm doesn't have an onboard relay) to the wire in the car that actually controls the domelight bulbs.

C Renner's Auto Electronix
My service is cheap, quick, and good - pick any two

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer