the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

remote starter won't activate


Post ReplyPost New Topic
< Prev Topic Next Topic >
jozzie 
Member - Posts: 5
Member spacespace
Joined: December 28, 2008
Location: Pennsylvania, United States
Posted: December 28, 2008 at 8:56 AM / IP Logged  
We are installing a AutoPage RS-602 into a 2009 Toyota Corolla, and it acts like it is disabled. The remote starter won't activate. It responds to the lock and unlock signal. But no response to the remote start.
Wiring is:
Violet = Starter
Red = 12V Constant
Yellow = Ignition 1
Pink = Ignition 2
Brown = Accessory
Wiring appears to be correct, it's been double checked and triple checked. But still no response to the remote start. Is this a programming issue?
I've installed these systems previously, but have not run into this issue before.
Any help would be appreciated.
TIA
muns15 
Member - Posts: 8
Member spacespace
Joined: December 28, 2008
Posted: December 28, 2008 at 9:28 AM / IP Logged  
It appears to be a programming issue. I had the same problem, make sure to go through the entire process on both remotes.
jozzie 
Member - Posts: 5
Member spacespace
Joined: December 28, 2008
Location: Pennsylvania, United States
Posted: December 28, 2008 at 9:33 AM / IP Logged  
muns15 wrote:
It appears to be a programming issue. I had the same problem, make sure to go through the entire process on both remotes.
We did this, and it still does not activate the remote start, it only allows for the lock/unlock at this point in time. Is there anything else that might be an issue?
TIA
big sexy lac 
Copper - Posts: 153
Copper spacespace
Joined: November 01, 2007
Location: Illinois, United States
Posted: December 28, 2008 at 9:47 AM / IP Logged  
Is there a 2nd starter wire that is not connected? Did you check the hood pin or neutral safety switch or brake switch? When you hit the remote start what happens, does the process start or just no responce at all?
well?
jozzie 
Member - Posts: 5
Member spacespace
Joined: December 28, 2008
Location: Pennsylvania, United States
Posted: December 28, 2008 at 9:54 AM / IP Logged  
big sexy lac wrote:
Is there a 2nd starter wire that is not connected? Did you check the hood pin or neutral safety switch or brake switch? When you hit the remote start what happens, does the process start or just no responce at all?
If you mean the Ignition 2 Input, yes it is connected. Yes, these other issues have been checked.
When you push the lock and unlock buttons you can hear the relays activate. When you push the remote start button, nothing happens, no LED Response, no audible clicking, nothing.
Have reset the factory default settings, reprogrammed both remotes, and still have the same issue - lock/unlock buttons work, but nothing from the remote start will activate.
muaiad97 
Copper - Posts: 207
Copper spacespace
Joined: April 08, 2003
Location: Canada
Posted: December 28, 2008 at 9:55 AM / IP Logged  
ok  do you hear any clicks  or  parking light flashing when you press  start bottun so we can help you with theat
jozzie 
Member - Posts: 5
Member spacespace
Joined: December 28, 2008
Location: Pennsylvania, United States
Posted: December 28, 2008 at 9:58 AM / IP Logged  
muaiad97 wrote:
ok  do you hear any clicks  or  parking light flashing when you press  start bottun so we can help you with theat
No, nothing at all when I push the start button with the remote.
muaiad97 
Copper - Posts: 207
Copper spacespace
Joined: April 08, 2003
Location: Canada
Posted: December 28, 2008 at 7:46 PM / IP Logged  

did you check the unit set up for  manual transmision or auto transmision  or you have  program the unit  for wich mode  or check  the parcking brake wire just disconected.

tedmond 
Gold - Posts: 4,610
Gold spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 06, 2007
Location: Ontario, Canada
Posted: December 28, 2008 at 10:37 PM / IP Logged  

about the second starter, this car has 2 ignitions, 2 starters and 1 accessory. did you power up the internal relays ? make sure you got no blown fuses

Mike M2 
Platinum - Posts: 2,652
Platinum spacespace
Joined: June 29, 2005
Location: United States
Posted: December 29, 2008 at 6:53 AM / IP Logged  
Well if it does nothing at all you can eliminate any ignition switch wiring as the problem. It would at least try to come on if it was. The issue is certainly not anteena as you get response for locks. That leaves only 3 possibilities, hood pin, neutral safety, or brake. Try disconnecting the hood and the brake and see if it goes....
Mike M2
Tech Manager
CS Dealer Services
Page of 2

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer