the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

matrix 2.2x with 904100 remote options


Post ReplyPost New Topic
< Prev Topic Next Topic >
Champcar_Fan 
Member - Posts: 6
Member spacespace
Joined: May 07, 2005
Location: United States
Posted: February 01, 2009 at 1:56 PM / IP Logged  
My original 487X remote started having problems and had to be replaced. Because of cost, I went with the 904100 replacement remote.
I've been able to program it to lock/unlock. I was wondering if there is a way to program the "panic" and the "Silent Mode" with this remote? The Slient Mode would be the preferable option if I can only program one of them, if at all.
Thanks!
Champcar_Fan 
Member - Posts: 6
Member spacespace
Joined: May 07, 2005
Location: United States
Posted: February 05, 2009 at 11:46 PM / IP Logged  
For anyone interested, here is the way I programmed the Silent Mode using the * button.
1. Open the driver’s door.
2. Turn the ignition on.
3. Select the receiver channel: Press and release the Valet/Program button the number of times necessary to access the desired channel. For silent mode, it is channel 2.
Press and hold the Valet/Program button once more. The siren will chirp and the LED will blink the number of times corresponding to the channel that is accessed.
4. Press the transmitter button. While HOLDING the Valet/Program switch, press the button from the transmitter that you wish to assign to the selected channel. (In my case, it is the * button. ) The unit will chirp once indicating that the channel has been entered.
5. Press the same transmitter button again. While still HOLDING the
Valet/Program switch, press the same transmitter button that you just
programmed. The siren will chirp twice to confirm that the desired channel has been successfully programmed to the button. If this step is not performed, the channel will not be programmed to the button. It is not possible to teach a transmitter button to the system more than once.
6. Release. Once the code is learned, the Valet/Program button can be released.
To exit the learn routine:
One long chirp indicates that Learn Routine has been exited. Learn Routine will be exited if any of the following occurs:
•     Ignition is turned off.
•     Door is closed.
•     Valet/Program button is pressed too many times.
•     More than 15 seconds elapse between steps.
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: February 07, 2009 at 7:13 AM / IP Logged  
N.B. to above if you have pos door contacts and are using the alarm's purple as your door trigger, ground the green.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, May 23, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer