clifford 590.2x remote start not avialabl

Just finish rebuilding my mr2 and installed a new clifford alarm. everything is working fine beside the remote start. when activate on the remote, the remote say its not available. In the manual, it mentions i need to go to an authorized dealer to activate it? Is there any information online that shows the activate code? Dont want to go to an dealer just to turn the function on.

Does lock/unlock functions work?  Have you tried to pair the remote to the brain?When all else fails, Read the Instructions

Support the12volt.com Make a Donation

The alarm works fine. Unlock lock, truck release all works. But when I push the remote start on the remote, it tells me on the screen that its not available. In the manual, it say it needs to go to an authorized dealer to have it activated?

Is the car Automatic or Manual?     What page in the manual says to go to an authorized dealer?

MTS mode is not enabled...Brake is on...Hood open...Toggle switch set to off or not plugged in...

Could you list what wires are connected to what wires on the car?....Make, Model, and year of car?

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

the car is a toyota mr2 1993 car is a Manual transmission mode is set on option 1 : manual brake is on Hood closed toggle switch is set to on. wiring, i follow this guide from another user. Primary harness (H1), 12-pin connector: H1/2 RED (+)12v CONSTANT INPUT BLACK/ Red Ignition Switch Harness H1/5 BLACK (-) CHASSIS GROUND Make a good ground H1/7 BLUE (-) TRUNK PIN/ INSTANT TRIGGER INPUT RED / white wire in drivers running board H1/8 GREEN (-) DOOR TRIGGER INPUT RED / white drivers kick panel below fuse box H1/9 BLACK/ WHITE (-) 200mA DOME LIGHT OUTPUT RED / white driver's side kick panel near the floor; Same as H1/7. H1/10 WHITE/ BLUE (-) REMOTE START/ TURBO TIMER ACTIVATION INPUT parking hand brake light H1/11 WHITE PARKING LIGHT OUTPUT Green (+) At 15A TAIL fuse H1/12 ORANGE (-) 500mA GROUND WHEN ARMED OUTPUT Cut to about 3" long and tape off Heavy gauge remote start, (H3) 10-pin connector: H3/1 PINK (+) IGNITION 1 INPUT/OUTPUT BLACK / YELLOW ignition harness H3/2 RED / WHITE (+) FUSED (30A) IGNITION 2 / FLEX RELAY INPUT 87 BLACK/ red ignition harness BLACK/ orange ignition harness H3/3 ORANGE (+) ACCESSORY OUTPUT Blue/red ignition harness H3/4 VIOLET (+) STARTER OUTPUT (CAR SIDE OF THE STARTER KILL) Red Ignition Switch Harness -CUT this wire. Connect this wire to the side of the red wire that runs into the dash. H3/5 GREEN (+) STARTER INPUT (KEY SIDE OF THE STARTER KILL WIRE) Red Ignition Switch Harness -CUT this wire. Connect this wire to the side of the red wire that runs to the ignition switch. H3/6 RED (+) FUSED (30A) IGNITION 1 INPUT BLACK/ red ignition harness H3/7 PINK/WHITE (+) IGNITION 2 / FLEX RELAY OUTPUT BLACK/ orange ignition harness H3/8 PINK/BLACK (+) FLEX RELAY INPUT 87A key side (if required) of FLEX RELAY Cut short and tape off H3/9 RED / BLACK (+) FUSED (30A) ACCESSORY/STARTER INPUT BLACK/ red ignition harness Remote start input, 5-pin connector: 1 BLACK/ WHITE (-) NEUTRAL SAFETY SWITCH INPUT Have not connected. 2 VIOLET/WHITE TACHOMETER INPUT WIRE IGt at ECU or the diagnostic box or the igniter. You may also leave this disconnected with more newer alarms if they have RPM sensing capabilities. 3 BROWN (+) BRAKE SHUTDOWN INPUT WIRE GREEN / WHITE at brake switch behind pedal 4 GRAY N/O or N/C (-) HOOD PIN SWITCH INPUT RED / green (Pin 13) at the stock theft deterrent ECU's harness is for all three stock hood sensors and easier to use than running three new switches. Door lock harness, 3-pin connector: 1 BLUE (+) LOCK (-) UNLOCK OUTPUT GREEN/ black (- unlock signal) driver kick panel 2 EMPTY NOT USED 3 GREEN (-) LOCK (+) UNLOCK OUTPUT RED / black (- lock signal) driver kick panel

Since it is a manual transmission, you MUST set the unit in the Manual Transmission Start ( MTS) Mode.

These steps are on page 42 and 43 of the owners manual. It must be set up every time you want to park the car and want to use the remote start.

It states that if not set to the MTS Mode, the remote will respond with REMOTE START NOT AVAILABLE

When all else fails, Read the Instructions

Support the12volt.com Make a Donation