the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

1999 Mazda 626 Alarm


Post ReplyPost New Topic
< Prev Topic Next Topic >
dwahle 
Member - Posts: 3
Member spacespace
Joined: January 05, 2005
Location: United States
Posted: January 05, 2005 at 10:56 AM / IP Logged  

Hi all,

I need help in the installation of an alarm with all the bells and whistles.  (Rmote start, windows roll down, alarm, etc) for a Mazda 626 4 cylinder (LX)   If you have any lessons learned, instructions or any advice it would be appreciated.

Dwahle
snguyen 
Silver - Posts: 281
Silver spacespace
Joined: October 09, 2003
Location: United States
Posted: January 05, 2005 at 11:34 AM / IP Logged  

Mazda

626

1998-1999

Remote Starter  Wiring Colors and Notes

Function

 

Vehicle  Color

Location

Start:

 

GREEN

IGNITION SWITCH HARNESS

Ignition  #1:

 

BLACK/ WHITE

IGNITION SWITCH HARNESS

Ignition #2:

 

BLACK/ RED

IGNITION SWITCH HARNESS

Ignition  #3:

 

N/A

Accessory:

 

BLUE

IGNITION SWITCH HARNESS

Brake  Light:

 

WHITE/ GREEN

AT SWITCH ABOVE BRAKE PEDAL **

Tach  Signal:

 

YELLOW

AT COIL MODULE

Parking Lights:

 

WHITE/ RED (+)

GREEN PLUG AT FUSE BOX

Headlights:

 

N/A

Diesel  Glow Plug:

 

Clutch  Bypass Wire:

 

Notes:

 ** Brake Wire Also Found In Driver's Kick Panel.

Mazda

626

1998-1999

Alarm and Keyless  Entry Wiring Colors and Notes

Function

 

Vehicle  Color

Location

Constant  +12 Volts:

 

BLACK

IGNITION SWITCH HARNESS

OEM Alarm Disarm:

 

Dome  Lights/Superv:

 

RED / WHITE (-)

AT FUSEBOX

OEM Horn:

 

Power  Lock:

 

BROWN / YELLOW (-)

FOUND AT A TAN MODULE NEAR THE HOOD RELEASE

Power  Unlock:

 

WHITE & BROWN / WHITE (-)

FOUND AT A TAN MODULE NEAR THE HOOD RELEASE***

Trunk  Release:

 

ORANGE

ABOVE FUSE BOX

Alarm  Input Wire:

 

RED / WHITE (-)

AT FUSEBOX

Notes:

***The white wire will unlock the drivers door only, and the BROWN / white will unlock the other doors. Use both wires and diode isolate each. See also Note #201 Negative trigger door locks.
dwahle 
Member - Posts: 3
Member spacespace
Joined: January 05, 2005
Location: United States
Posted: January 05, 2005 at 12:42 PM / IP Logged  

THanks for the information.

I don't suppose that you have any installation instructions?

Thanks again.

Dwahle
snguyen 
Silver - Posts: 281
Silver spacespace
Joined: October 09, 2003
Location: United States
Posted: January 05, 2005 at 12:45 PM / IP Logged  
what are you looking for?
dwahle 
Member - Posts: 3
Member spacespace
Joined: January 05, 2005
Location: United States
Posted: January 05, 2005 at 12:50 PM / IP Logged  

Any help or instruction on where to start, and the best way to do it.

THanks!

Dwahle
DiscoKing 
Member - Posts: 9
Member spacespace
Joined: September 27, 2003
Location: United States
Posted: January 05, 2005 at 5:32 PM / IP Logged  
I'm actually in the middle of an install on a 1998.  Connections went pretty smooth.  I started with power connections, then safety cutouts, and then the locks and lights.  The only mix up I made was with the + and - parking light wires.  Keyless entry is working great but I can't get the Remote Start to do anything.  Do you know if the 626 needs an interface module to bypass a transponder?  The salesman told the guy I'm doing this for that he didn't need one but I thought it did.  That would make sense why the system is not doing anything.
DiscoKing 
Member - Posts: 9
Member spacespace
Joined: September 27, 2003
Location: United States
Posted: January 05, 2005 at 9:32 PM / IP Logged  
Thanks for the info.  That didn't work either so I guess I'll have to keep checking wires.  The other funny thing I found was that the hood switch has >1 ohm difference between open and closed.  Does that make sense cause it doesn't sound like enough to me.  Usually switches should have an open reading in one of the positions.
DiscoKing 
Member - Posts: 9
Member spacespace
Joined: September 27, 2003
Location: United States
Posted: January 08, 2005 at 7:19 PM / IP Logged  
Nada.  I get absolutely nothing.  With key in the ignition and the hood switch disconnected nothing happens.  Not even a sound that it is attempting anything.  I have double checked the wiring and can find nothing wrong.  A bit frustrating.  Ugh.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer