the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

ungo remote start


Post ReplyPost New Topic
< Prev Topic Next Topic >
fatheadjames 
Member - Posts: 7
Member spacespace
Joined: December 16, 2002
Location: United States
Posted: December 05, 2005 at 7:23 PM / IP Logged  
I'm trying to find the installation manual for a saa4295 remote start piece. It is installed along witha ms8200 in the truck I just bought. It currently doesn't work and am wanting to reinstall it. Also if there are any programing directions for it. Thanks in advance.
tacalin 
Member - Posts: 21
Member spacespace
Joined: August 12, 2005
Location: Canada
Posted: December 06, 2005 at 5:47 AM / IP Logged  
with engine running press the button(s) for aux. function which engage the remote start. you must to hear the relays. remove the key from ignition and see if the engine still running. if you have a manual transmission must have the hand-brake engaged before pressing the button. the single programing feature for this model is engine run time. try this and if don't start I'll send you the wires.
fatheadjames 
Member - Posts: 7
Member spacespace
Joined: December 16, 2002
Location: United States
Posted: December 06, 2005 at 12:08 PM / IP Logged  
I tired that and nothing happened; so if you can send me that info it would be great. You can post it here or e-mail me. Thanks for the help.
fatheadjames@hotmail.com
tacalin 
Member - Posts: 21
Member spacespace
Joined: August 12, 2005
Location: Canada
Posted: December 07, 2005 at 3:26 AM / IP Logged  
Main connector:
violet - ign out (+) -> violet (don't connect these two wires at the ign key. you will burn a transistor on remote start)
green - (+) led out -> red led wire
yellow - (-) start command -> aux. function yellow/....
WHITE/ brown - (-) starter disable in -> blue
BLACK/ white - (-) sensor defeat out -> gray/black
black - ground
PURPLE / white - (+) ign input -> connect with purple large wire
blue/black - (+) brake pedal input
GREEN/ purple - (+) wait to start input -> connect with blue large wire (for diesel engine connect to glow plug)
orange - (-) running light (don't use)
GREEN/ YELLOW - (-) hood switch
WHITE/ yellow - tach input
Large wires:
purple - IGN
blue - STARTER (to starter)
red - +12V
white - ACC
yellow - STARTER (to ign key)
2 pin connector (back):
WHITE/ orange - (-) hand brake (use just for manual transmission)
WHITE/ blue - not used
For run time programing: system off, engine off. open the hood and press the remote start activation button. press 1 time = 1 minute, press 2 times = 2 minutes.....(max. 256 minutes). for each press led will go on.
good luck! you will need.
fatheadjames 
Member - Posts: 7
Member spacespace
Joined: December 16, 2002
Location: United States
Posted: December 08, 2005 at 10:23 PM / IP Logged  
Thanks for the info man. I guess this thing is just fubar. Oh well guess I'll buy a new alarm.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer