the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

wiring twin fans with parallel resistors?


Post ReplyPost New Topic
< Prev Topic Next Topic >
cheshire190e 
Member - Posts: 1
Member spacespace
Joined: February 15, 2012
Location: United Kingdom
Posted: February 15, 2012 at 2:02 AM / IP Logged  
Hi everyone,
I have recently purchased some twin 12" fans for my car and having a little trouble trying to work out how to wire them up.
Basically what I want to achieve is to have the fans permanently running at a low speed whilst the engine is running, then kick up to full power once the car reaches a set temperature.
I have a fan controller so I can output the 12v for high speed at a set temperature so that parts fine. The bit I am struggling with is how to make the fans run at a low speed, and how to switch from the low to high speed.
What I was thinking is i could either connect the fans in series for low speed, and switch to parallel for high speed. Or use a seperate source 12v and 2 parallel resistors to give me the low speed.
The part I am confused about is that if I connect them in series so each fan has 6v for the low setting, when the temp reaches 100oC and the fan controller kicks in. will sending a further 12v to the fans in parallel cause damage? or will i need another relay to switch the series circuit off, when the parallel circuit switches on.
Any help would be greatly appreciated.
Cheers
Matt
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: February 15, 2012 at 4:00 AM / IP Logged  
Using resistors means you will need a handy fire extinguisher. Those fans are probably drawing in excess of 40 amps each on start-up.PM Oldspark for the answer which will probably be a variable voltage device.
oldspark 
Gold - Posts: 4,913
Gold spacespace
Joined: November 03, 2008
Location: Australia
Posted: February 15, 2012 at 7:33 AM / IP Logged  
Don't PM me - I'm not sure....
It seems many use resistors for slow speed - a low temp relay with series resistor for slow, and a high temp relay direct to the fans effectively bypassing or shorting out the resistor for fast speed.
I'd expect 6-7V when in series is too low a voltage, but a test should confirm.
The Wattage of the resistor is VV/R or IIR where V is the voltage drop, I is the current, R is the resistance.
EG - if 40A and a 5V drop is required, the resistor is 5V/40A = 0.125 Ohms (from V=IR) and its Wattage = 40 x 40 x .125 = 200W. (Maybe ten 1 Ohm 20W resistors in parallel? Mind you, 200W is a lot of heat...)
I'd expect a MOSFET PWM circuit is used.   MOSFETs that handle 100A are cheap (a $few) and PWM isn't too hard - either my elsewhere posted 555 PWM circuit (0.1% - 99.9% duty cycle) or others, or a modern vehicle's dashlight dimmer (usually good for ~10A) that drives a MOSFET.
But if going to that trouble, why not a proportional system - eg, off when not needed (normal cruising etc), then some minimum speed when warm enough top be required (maybe 40-60%?), rising to 100% for hot?
And the easiest way - a PIC or PICAXE08M (8 pins). It has an analog to digital converter (ADC) to read the temp sensor, and PWM output(s), and space for ~80 lines of code. The newer superseding 08M2 has more - like space for over 2,000 lines of code; parallel tasking, more pin functions, etc. (They have done the clever thing - the M2's share the same guts so the 8, 18, 26 (or whatever) pin packages have the same program space... (Not that I've used one yet, but with that coding space, I think the time is right....)
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: February 15, 2012 at 10:59 AM / IP Logged  
I see what you're getting at Peter, Bosch type relays activate on 7.5 volts, probably need a 6 volt coil relay.
Why would you need 2 fans on all the time, especially in Cheshire?
I'm in North West London, more stop starting than anywhere else in the UK and I don't need my fans on, the only time I ever hear them is when I turn on the AC.
i am an idiot 
Platinum - Posts: 13,693
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: February 15, 2012 at 10:17 PM / IP Logged  
Connect the fans in series.  Does this give you the desired LOW speed?  If so, you can use 2 relays and a diagram here in the relay section.  The diagram is labeled something about running speakers in series and parallel.
i am an idiot 
Platinum - Posts: 13,693
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: February 15, 2012 at 10:40 PM / IP Logged  

Voice Coil one = Fan one.  Voice Coil Two = Fan Two.    Amplifier output one channel = +12 V and Ground.

wiring twin fans with parallel resistors? -- posted image.
oldspark 
Gold - Posts: 4,913
Gold spacespace
Joined: November 03, 2008
Location: Australia
Posted: February 17, 2012 at 12:49 AM / IP Logged  
Voice coil? Is someone thinking of disk drives...?
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: February 17, 2012 at 12:51 AM / IP Logged  
It was an ANALOGY; have a cup of coffee Mr. I simply said substitute fans motors for speakers.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer