the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

thunderbird kick panels


Post ReplyPost New Topic
< Prev Topic Next Topic >
noakes75 
Copper - Posts: 58
Copper spacespace
Joined: January 18, 2004
Location: United States
Posted: April 30, 2005 at 2:48 PM / IP Logged  

hey, i got a 95 thunderbird, and i thought about making kickpanels for some 5 1/4s but i have no idea on how to get started. ive delt with fiberglass before but not in this type or application. ive made a few sub boxes so i have the basic idea, just its still kinda confusing to me. i know u need to use aluminum foil or something to that effect for the casting. i understand that part of things, but the part that really gets me is that  on the factory kickpanel it runs about 1/2 way up the door crease. (the little strip inbetween the dash and the out side. and i wasnt sure how to go about that. itll be a while before if get started. im in the army, and still in training, but any ideas would be great, that way i would be able to get started on it and pop it right out when i got started. thanks

front leaning rest postion MOVE
drvnbysound 
Silver - Posts: 289
Silver spacespace
Joined: May 06, 2002
Location: United States
Posted: May 01, 2005 at 12:10 PM / IP Logged  
The easiest thing for your application to do is to actually use the existing stock panel, because of that strip. I would cut and mount my MDF speaker rings to each panel, angled/imaged, etc. Then spray the edges of the inside of the panel with some spray adhesive and wrap the bottom portion of the kickpanel with mold fabric. You should be able to stretch the mold fabric around to the other side of the panel and adhere to the spray adhesive. Do the same around the front side, however you will need to cut it off before you get to the long strip. After you add your resin to the fleece, you can add bondo and taper the mold fabric into the stock ABS strip.
Its a lot easier to understand this process if you have done it before. Good luck with your project.
noakes75 
Copper - Posts: 58
Copper spacespace
Joined: January 18, 2004
Location: United States
Posted: May 08, 2005 at 8:52 AM / IP Logged  
yea, but i tried something similar to that before and it looked good and all, but when i was almost done with it i had a problem with the fiberglass lifting from the ABS. any suggestions on that?
front leaning rest postion MOVE
itmdtr 
Copper - Posts: 131
Copper spacespace
Joined: May 23, 2003
Location: United States
Posted: May 13, 2005 at 6:38 AM / IP Logged  

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer