2002 gmc 2500

Home / the12volt's Install Bay / Car Security and Convenience / 2002 gmc 2500 (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

brakisshuro

Member - Posts: 33

Joined: December 09, 2007

Location: Idaho, United States

Posted: January 04, 2008 at 11:30 PM / IP Logged

I have put in a compustar 4200 and a fortin int-sl. There is only two wires on the bypass to connect, which I have done. I am not getting the bypass to learn the code. I follow the instructions but I am not getting the confrimation from it. I unhooked it and tried a ads module programmed for gm and same thing, will not learn the code. Any ideas?

519civiconair

Copper - Posts: 50

Joined: October 30, 2007

Location: Ontario, Canada

Posted: January 05, 2008 at 7:04 AM / IP Logged

Are you sure you have the right data-bus wire? If so is the unit entering programming mode or?? need more info....

F.B.S.S air ride is the only way to roll

brakisshuro

Member - Posts: 33

Joined: December 09, 2007

Location: Idaho, United States

Posted: January 05, 2008 at 8:04 AM / IP Logged

yes I have pin 2, and it is entering programming mode and then it is dropping out when I try to learn the key, or gives me a a red light meaning it is not programmed correctly

519civiconair

Copper - Posts: 50

Joined: October 30, 2007

Location: Ontario, Canada

Posted: January 05, 2008 at 8:19 AM / IP Logged

Do you have the keysense wire hooked up?

F.B.S.S air ride is the only way to roll

519civiconair

Copper - Posts: 50

Joined: October 30, 2007

Location: Ontario, Canada

Posted: January 05, 2008 at 8:48 AM / IP Logged

sorry wrong post...... ok what are you doing to get into programming mode? is it all Unplugged press and hold prog. button plug in conn.1 LED turns on? then conn.2 (careful not to reverse) turn key to ign. LED flashes rapidly? release prog. button and start truck and the LED stays ON????

F.B.S.S air ride is the only way to roll

brakisshuro

Member - Posts: 33

Joined: December 09, 2007

Location: Idaho, United States

Posted: January 05, 2008 at 9:28 AM / IP Logged

no it was flashing and turning off before I could start the truck. Anyways I figured out, I swapped out my module with a ads-dl and programmed it with just te tb function, and first time programmed up. thank you for your guys help.

moonliter

Copper - Posts: 322

Joined: February 28, 2007

Location: Canada

Posted: January 05, 2008 at 11:45 AM / IP Logged

int-sl is only compatible for gmc model year 03 and up. unless it is sonama or a 02 envoy.

brakisshuro

Member - Posts: 33

Joined: December 09, 2007

Location: Idaho, United States

Posted: January 06, 2008 at 12:21 AM / IP Logged

in the manual and on their website it lists it as a active module for 98 and up

moonliter

Copper - Posts: 322

Joined: February 28, 2007

Location: Canada

Posted: January 06, 2008 at 10:09 PM / IP Logged

It is kind of waste just to use it to bypass passlock only. It couldn't do doorlock, arm/disarm and parklights etc. etc....on your model year. You could get a passlock-sl2 instead for half the price, IMO.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

2002 gmc 2500

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.