viper idatalink gm factory alarm

Home / the12volt's Install Bay / Car Security and Convenience / viper idatalink gm factory alarm (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

gottago

Member - Posts: 2

Joined: February 11, 2011

Location: Ontario, Canada

Posted: February 11, 2011 at 10:08 PM / IP Logged

I have a 06 envoy with factory alarm and I installed a viper 5901 alarm remote start with a idatalink dl gm1 bypass module, every thing works ok except when the doors are locked for awhile 20 min. or so and you start the truck the factory alarm will go off. To get it to start without tripping off the alarm you have to unlock then relock then start truck or unlock then start truck and then lock it up again.

thanks Gottago

kreg357

Platinum - Posts: 7,791

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: January 30, 2009

Location: Pennsylvania, United States

Posted: February 12, 2011 at 6:04 AM / IP Logged

Are you running D2D or W2W between the Viper and the ADS DL?

If running D2D, did you flash the ADS DL module with DBI DL GM1 firmware? (My preference is to run W2W and hard wire all connections between the remote starter and the bypass module. Strange things happen in D2D mode....)

If running W2W did you connect the Viper H2/1 Light GREEN/ Black (-) 200mA Factory Alarm Disarm Output to the ADS DL Brown (-) Disarm wire?

Soldering is fun!

Mike M2

Platinum - Posts: 2,652

Joined: June 29, 2005

Location: United States

Posted: February 12, 2011 at 8:23 AM / IP Logged

Kreg i don't know about anyone else but have had a few issues using the pulse before start to disarm the factory alarm when using the Idatalink bypasses. It's like the pulse isn't long enough, i dunno. I started connecting the brown disarm to the blue status wire and so far i haven't had any issues....

Mike M2

Tech Manager

CS Dealer Services

kreg357

Platinum - Posts: 7,791

Joined: January 30, 2009

Location: Pennsylvania, United States

Posted: February 12, 2011 at 9:03 AM / IP Logged

Hi, Mike! Thanks for the heads-up. I haven't encountered that problem. Most R/S's output a .75 sec disarm pulse but I never put a scope on it to measure the length. I don't use Viper so I wonder if its an issue with them. Connecting to GWR will definitely cure that problem!

Soldering is fun!

gottago

Member - Posts: 2

Joined: February 11, 2011

Location: Ontario, Canada

Posted: February 12, 2011 at 1:44 PM / IP Logged

Sorry guys away for the morning,I'm going to have to check my paper work. I will report back

Thanks Gotta Go

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

viper idatalink gm factory alarm

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.