Hello all, first time posting, long time lurker. I think I am almost ready to tackle my install, but I have a few wires that I am still uncertain about.
I am installing a Viper 4806v with a DBALL2 into a 2014 Toyota Tacoma.
I am uncertain about the following wires on the Viper and where to connect them. Especially the H3/5 since my truck has a starter 2. Everything marked with a ????? I am unsure about.
All help is greatly appreciated!!
Vehicle Information: 2014 Toyota Tacoma DCSB (G-key)
Alarm / Remote Start Unit: Viper 4806v
Bypass Module: DBALL2
Alarm / Remote Start / Bypass Unit Vehicle
Connection Color Description Color Polarity Location:
Main Harness, 6-pin connector
H1/1 RED (+)12VDC CONSTANT INPUT WHITE/ BLUE + Ignition switch, white 8 pin plug, pin 4
H1/2 BLACK (-) CHASSIS GROUND GROUND - GROUND
H1/3 BROWN (-) 200mA HORN HONK OUTPUT NOT USED
H1/4 WHITE/ BROWN LIGHT FLASH ISOLATION WIRE - PIN 87a light flash relay NOT USED
H1/5 WHITE PIN 30 of LIGHT FLASH RELAY GREEN + Dash fuse box, white 13 pin plug, pin 10
H1/6 ORANGE 500 mA GROUND WHEN ARMED OUTPUT NOT USED
Door Lock, 3-pin connector
1 BLUE 500mA (-) UNLOCK OUTPUT GREEN/ BLACK - Driver kick panel, gray 10 pin plug, pin 8
2 EMPTY NOT USED NOT USED
3 GREEN 500mA (-) LOCK OUTPUT VIOLET - Driver kick panel, gray 10 pin plug, pin 4
Auxiliary/Shutdown Harness, 24-pin connector
H2/1 PINK/WHITE (-) 200mA Ignition 2/Flex OUTPUT ?????
H2/2 BLUE/WHITE (-) 200mA 2ND STATUS /REAR DEFOGGER OUTPUT NOT USED
H2/3 RED / WHITE (-) 200mA TRUNK RELEASE OUTPUT (NOT USED) NOT USED
H2/4 BLACK / YELLOW (-) 200mA DOME LIGHT OUTPUT
H2/5 DARK BLUE (-) 200mA STATUS OUTPUT NOT USED
H2/6 WHITE/ BLACK (-) 200mA AUX 3 OUTPUT NOT USED
H2/7 WHITE/ VIOLET (-) 200mA AUX 1 OUTPUT NOT USED
H2/8 ORANGE / BLACK (-) 200mA AUX 4 OUTPUT NOT USED
H2/9 GRAY (-) HOOD PIN INPUT (NC OR NO) Hood pin installed
H2/10 BLUE* FACTORY HORN INPUT
H2/11 WHITE/ BLUE ACTIVATION INPUT NOT USED
H2/12 VIOLET/WHITE** TACHOMETER INPUT OBDII Pin 9
H2/13 BLACK/ WHITE*** (-) NEUTRAL SAFETY /PARKING BRAKE INPUT GROUND - GROUND
H2/14 GREEN/ BLACK (-) 200mA FACTORY ALARM DISARM OUTPUT ?????
H2/15 GREEN** (-) DOOR INPUT ?????
H2/16 EMPTY NOT USED NOT USED
H2/17 PINK (-) 200mA IGNITION 1 OUTPUT NOT USED
H2/18 VIOLET** (+) DOOR INPUT NOT USED
H2/19 VIOLET/BLACK (-) 200mA AUX 2 OUTPUT NOT USED
H2/20 BROWN (+) BRAKE SHUTDOWN INPUT BLUE + Dash fuse box, white 13 pin plug, pin 13
H2/21 VIOLET / YELLOW (-) 200mA STARTER OUTPUT ?????
H2/22 GRAY/BLACK (-) DIESEL WAIT TO START INPUT NOT USED
H2/23 ORANGE (-) 200mA ACCESSORY OUTPUT NOT USED
H2/24 GREEN / WHITE (-) 200mA FACTORY ALARM ARM OUTPUT ?????
Remote Start, 8-pin connector
H3/1 RED / BLACK (+) 12VDC CONSTANT INPUT for ACC and starter relays WHITE/ BLUE + Ignition switch, white 8 pin plug, pin 4
H3/2 PINK/BLACK (+) FLEX RELAY INPUT 87A key side (if required) of FLEX RELAY NOT USED
H3/3 PINK/WHITE (+) IGNITION 2 / FLEX RELAY OUTPUT BLUE / YELLOW + Ignition switch, white 8 pin plug, pin 1
H3/4 RED (+) 12VDC CONSTANT INPUT for ignition 1 relay WHITE/ BLUE + Ignition switch, white 8 pin plug, pin 4
H3/5 VIOLET (+) STARTER OUTPUT ?????
H3/6 ORANGE (+) ACCESSORY OUTPUT NOT USED
H3/7 RED / WHITE (+) 12VDC CONSTANT INPUT for ignition 2 and flex relays WHITE/ RED + Ignition switch, white 8 pin plug, pin 5
H3/8 PINK (+) IGNITION 1 INPUT/OUTPUT BLACK/ RED + Ignition switch, white 8 pin plug, pin 6
DBALL 2
Blue, 14-pin connector
3 TAN/BLACK HS CAN High OBDII Pin 6
4 TAN HS CAN Low OBDII Pin 14
Red, 12-pin connector
10 YELLOW/BLACK SIL (Safety Integrity Level) OBDII Pin 7
Black, 10-pin connector
9 PINK (+) IGNITION INPUT BLACK/ RED + Ignition switch, white 8 pin plug, pin 6
D2D, 4-pin connector Connect directly to Viper brain
I know I have to use a few relays somewhere, but I am confused as to which wires. THANKS AGAIN!