the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2000 blazer service engine light stays on


Post ReplyPost New Topic
< Prev Topic Next Topic >
tumbleweed10 
Member - Posts: 3
Member spacespace
Joined: November 16, 2003
Posted: November 16, 2003 at 11:09 AM / IP Logged  

Just installed a remote starter (bulldog rs82) with part #791 and service engine light stays on can anyone help me with this problem

thank you

Dave

Haku 
Copper - Posts: 204
Copper spacespace
Joined: November 22, 2002
Location: United States
Posted: November 16, 2003 at 11:22 AM / IP Logged  

I had the same problem with a 2001 Blazer.  What passlock bypass did you use?  Im guessing not a PLDATA.  I wont use the GMATA, or same on them anymore because of that problem.  When you remote start the truck, then get in it and turn the key to the on postion, the security light comes on, but the vehicle stays running, and if you start it with a key, the secuity light does not come on.  Nothing I did would fix it, untill I switched out the bypass.

Hope this helps

Hak
Siemens Autostart
tumbleweed10 
Member - Posts: 3
Member spacespace
Joined: November 16, 2003
Posted: November 16, 2003 at 11:46 AM / IP Logged  
i used the part#791 relay that bulldog has and mine stays on even if starting with key
ck auto 
Copper - Posts: 257
Copper spacespace
Joined: September 20, 2003
Location: Canada
Posted: November 16, 2003 at 12:14 PM / IP Logged  

soundslikeyou missed 2nd ing wire it should be white if no second ing on rs use a relay and use out will  runining.

kirk

Alpine Guy 
Platinum - Posts: 2,478
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: October 18, 2003
Location: Canada
Posted: November 16, 2003 at 1:50 PM / IP Logged  
yup, 2nd ignition wire,,it does that, and the light will stay on till the engine is turned off.  Tranny damage can occure aparently if you don't hook it up.
Haku 
Copper - Posts: 204
Copper spacespace
Joined: November 22, 2002
Location: United States
Posted: November 16, 2003 at 1:52 PM / IP Logged  

Ok, I think I was still asleep when I read this, .. I thought it was the security light... so disregard my ramblings.

Hak
Siemens Autostart
tumbleweed10 
Member - Posts: 3
Member spacespace
Joined: November 16, 2003
Posted: November 16, 2003 at 2:06 PM / IP Logged  
is 2 nd ign. wire real small
ck auto 
Copper - Posts: 257
Copper spacespace
Joined: September 20, 2003
Location: Canada
Posted: November 16, 2003 at 10:05 PM / IP Logged  

hi 2nd ing wire is generaly same size but could be smaller guage just meter it and see iff it is 12v in run and while cranking and show nothing when iun off position

kirk

Digger67 
Member - Posts: 23
Member spacespace
Joined: November 12, 2003
Location: Canada
Posted: November 17, 2003 at 9:35 AM / IP Logged  
Yes the second IGN wire is white and smaller then the IGN 1 wire. just did an install on a 2000 Blazer. If the 2nd IGN wire is not hooked up the Service light will come on and the tranny wont shift out of second when remote strated.
Alpine Guy 
Platinum - Posts: 2,478
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: October 18, 2003
Location: Canada
Posted: November 17, 2003 at 8:11 PM / IP Logged  

i just sent a private message to tumbleweed10 , but i should get you guys to check it over to be shure its correct.  I'll just cut and past, im to lazy to type again.

Im doing this off the top of my head, here it goes:

First you will need a bosch relay.  One you have the relay you need to do the connections the way i tell you.

Pin 87 goes to your 2nd ignition wire  ( i think its white on your vehicle)

Pin 85 goes to the 1st ignition wire ( i think its pink on your vehicle)

Pin 30 goes to a constant 12V power source

Pin 86 hooks up to your starters constant (-) output.  Be shure to put a diode inline with the band facing the starter.  Do the diode on both the relay wire and the bypass wire, it is mandatory or you will fry stuff.   All you need is a low voltage diode.

Pin 87a is not needed.

Hope this helps.  Be shure to solder and tape all your connections.

so good? or what??  i usually look at my diagram at work, but i don't have it here so its a guess.


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer