the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Priority Driver Unlock Feature


Post ReplyPost New Topic
< Prev Topic Next Topic >
LithiumCobalt 
Member - Posts: 10
Member spacespace
Joined: May 22, 2003
Location: United States
Posted: June 12, 2004 at 12:49 PM / IP Logged  
I have a 1992 Buick Regal 4 door and recently cut the factory RKE unit because it was faulty.  However, now my drivers door will not lock/unlock by the press of the button but all the other passenger doors do.  If I hook up the tan unlock wire for the driver door to ground the driver door will lock fine but in order to lock it, it requires positive on the same wire.  I'm trying to install a new GM aftermarket RKE (actually a Directed-DEI unit) but cannot figure out how to interface the unit with my positive lock system.  I think this is a common problem on most GM's with this type of RKE configuration but haven't found any good way to go about this as of yet.  Any help would be appreciated.
draasch 
Gold - Posts: 2,172
Gold spacespace
Joined: February 07, 2003
Location: Florida, United States
Posted: June 12, 2004 at 1:44 PM / IP Logged  
is this a front wheel drive???
if so see if this will help:
Power Lock LIGHT BLUE DRIVER KICK PANEL #202
Power Unlock BLACK DRIVER KICK PANEL #202
AL 100 / VIP-4000
RKE Module SEE NOTES *
Motor Lock GRAY AT OEM RELAYS **
Motor Unlock TAN OR TAN/WHT AT OEM RELAYS ** SEE NOTES ***
Drv Door Unlock TAN OR TAN/WHT *** AT KEYLESS OR IN DRIVER KICK PANEL **
OEM Relays PASSENGER KICK PANEL
Addon Security Type SEE NOTES **** #221,#223
* (1988)No OEM Keyless (1989-90)Under Passenger Rear Seat (1991-93)Located On Right Rear Package Shelf Near Right Speaker **Circuit Type: Reversal Rest At Ground *** (1988-90)TAN/WHT (1991-93)TAN **** (1989-90)Type 1 Without Driver Priority Or Type 3 With Driver Priority (1991-93)
Good Luck
David
Ace Security
813-376-9778
Tampa
Donate to the 12volt
LithiumCobalt 
Member - Posts: 10
Member spacespace
Joined: May 22, 2003
Location: United States
Posted: June 12, 2004 at 10:50 PM / IP Logged  
It is a front wheel drive, and as far as I know I have all of the wires correctly hooked up at the rear of the vehicle where the old keyless entry module was located.  Problem is, the driver's side switch will lock doors but not unlock and passenger side will lock also but not unlock.
LithiumCobalt 
Member - Posts: 10
Member spacespace
Joined: May 22, 2003
Location: United States
Posted: June 12, 2004 at 10:52 PM / IP Logged  
It's like removing the stock keyless entry unit incompletes some of the circuits for the switches disabling their functionality...I'm stupmed.
LithiumCobalt 
Member - Posts: 10
Member spacespace
Joined: May 22, 2003
Location: United States
Posted: June 12, 2004 at 11:04 PM / IP Logged  
Everything works besides the unlock feature on both switches
draasch 
Gold - Posts: 2,172
Gold spacespace
Joined: February 07, 2003
Location: Florida, United States
Posted: June 13, 2004 at 6:46 PM / IP Logged  
do u still have the old unit??
Good Luck
David
Ace Security
813-376-9778
Tampa
Donate to the 12volt
sroth140 
Silver - Posts: 513
Silver spacespace
Joined: August 27, 2003
Location: United States
Posted: June 14, 2004 at 12:06 AM / IP Logged  

i think it was on one of those cars i had to gab the black wire in the pass. kick.  the one in the drivers wouldnt test right.

MECP certified installer
LithiumCobalt 
Member - Posts: 10
Member spacespace
Joined: May 22, 2003
Location: United States
Posted: June 18, 2004 at 6:30 PM / IP Logged  
YEs, I still have the old unit.  Just simply unhooked it.  It's strange because all of my new keyless entry feaures work just fine (priority unlock and such).  It is the original interior lock buttons that are giving my grief.  The drivers side will lock all of the doors with no problem (including itself), however, the drivers side button will NOT unlock the driver door.  The passenger side button will lock them all also but it will not unlock the driver door either.  Anyone got any ideas?
LithiumCobalt 
Member - Posts: 10
Member spacespace
Joined: May 22, 2003
Location: United States
Posted: July 02, 2004 at 11:27 PM / IP Logged  
Finally figured it out.  There's an additional relay needed to be added inline with the driver's motor wire enabling the unlock wire for the rest of the doors to trigger the drivers door as well.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer