the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

autopage starter kill relay


Post ReplyPost New Topic
< Prev Topic Next Topic >
instalador 
Member - Posts: 8
Member spacespace
Joined: February 07, 2006
Location: United States
Posted: February 22, 2006 at 11:54 AM / IP Logged  

autopage starter kill relay -- posted image.hello evryone.i'm installing a auto page alarm in tacoma 96 4x2

im confused,abouth the killstar relay. inthe manual don't xplain well.the relay has 4 wires. but shoulike  this  .star wire motor side (purple (pin 87a) yellowwire(pin30)star wire key side. till here im ok. here is the confused

((12v(+)  red wire(85pin)  ingnition)     its constan or only  when crank

betwen red wire( 85pin) diode to  (white wire)86pin'this white wire go to alarma sistem!!    its only the red wire confused??thaks 4 any sugestion

electriope88
Velocity Motors 
Moderator - Posts: 12,488
Moderator spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Fabrication. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: March 08, 2002
Location: Manitoba, Canada
Posted: February 22, 2006 at 12:54 PM / IP Logged  
A starter disable relay when no power is going through the relay separates your starter wire. When the IGN is on and the system outputs a (-) signal to pin 86 then the starter wire is reconnected allowing the vehicle to start with the key.
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
kohara73 
Copper - Posts: 192
Copper spacespace
Joined: December 08, 2005
Location: Canada
Posted: February 22, 2006 at 3:09 PM / IP Logged  
Actually Jeff you're a little backwards there.  The starter wire is connected until the relay gets power from igniton and ground from alarm. This then connects 30 to 87 and no start, because starter wire is on 87a. So to answer the question, the ground is present anytime the alarm is armed.  If you turn the ignition on, it separates the starter wire and the car won't start.  Unarm the alarm, no ground, no closed coil on relay, car starts.  They are probably tied to ignition instead of constant +12V to save power and only be active if the igniton is turned on.  Hope this helps.
Keith
dualsport 
Silver - Posts: 983
Silver spacespace
Joined: September 27, 2005
Location: United States
Posted: February 22, 2006 at 5:56 PM / IP Logged  
It could be set up either way; depends on whether you want it more failsafe as far as starting if the alarm malfunctions or preventing a start if it gets ripped out.
With the usual starter kill setup, if the alarm power is disabled, will the starter kill relay output still be able to provide a ground signal to switch the relay? If not, then the car will start normally.
Doing it backwards from the usual way, using the 87-30 contact pair will require the relay to be energized to start, which may be more secure, but runs the risk of disabling the car if you lose alarm power.
instalador 
Member - Posts: 8
Member spacespace
Joined: February 07, 2006
Location: United States
Posted: February 23, 2006 at 10:07 AM / IP Logged  
thank you jeff
electriope88
instalador 
Member - Posts: 8
Member spacespace
Joined: February 07, 2006
Location: United States
Posted: February 23, 2006 at 10:11 AM / IP Logged  
thank you keith  4  u help  ? please! can you send me  picture of the diagram if  is posible.thxx  again
electriope88
instalador 
Member - Posts: 8
Member spacespace
Joined: February 07, 2006
Location: United States
Posted: February 23, 2006 at 10:15 AM / IP Logged  
autopage starter kill relay -- posted image. thank you !!  dual sport
electriope88
kohara73 
Copper - Posts: 192
Copper spacespace
Joined: December 08, 2005
Location: Canada
Posted: February 23, 2006 at 7:57 PM / IP Logged  

https://www.the12volt.com/relays/page2.asp

The top one is what I believe you are are trying to accomplish.

Keith

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer