the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Please help Ohm load


Post ReplyPost New Topic
< Prev Topic Next Topic >
mgeorge 
Member - Posts: 3
Member spacespace
Joined: January 08, 2003
Location: United States
Posted: January 08, 2003 at 8:29 PM / IP Logged  
I have 3 subwoofers dual voice coil with 4 ohms each voice coil.  I would like to connect them all to one amp.  Can I connect them in a combination of serial and parallel? Thank you for your help.
auex 
Platinum - Posts: 5,041
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: December 23, 2002
Location: Arizona, United States
Posted: January 08, 2003 at 9:36 PM / IP Logged  
Sure you can.  First what is the amp stable at?  Each sub can either be 2 or 8 ohms.  If the amp is stable to 4 ohms bridged (most two channel amps are this way ) then run the voice coils in parrallel and wire the subs in series for a ohm load of 6 ohms.  You can achieve a 2.6 ohm load if you wire the voice coils in series and then wire the subs in parrallel.  You could get some other loads by doing different things but I personally think wiring every thing the same is better, the coils the same and the subs the same, that each sub will get the same amount of power.
Certified Security Specialist
Always check info with a digital multimeter.
I promise to be good.
Tell Darwin I sent you.
I've been sick lately, sorry I won't be on much.
mgeorge 
Member - Posts: 3
Member spacespace
Joined: January 08, 2003
Location: United States
Posted: January 08, 2003 at 10:09 PM / IP Logged  
Auex thank you for replying.  The amp is stable at 4 ohms but it gets twice the power at 2 ohms.  It is a JBL bp1200.1.  I was also wondering if I could connect a second JBL bp1200.1 to help power the 3 MBQuart PWD 254 with 300 watts rms 750 watts max.  The amp produces 600 watts at 4 ohms and 1200 watts at 2 ohms. Thank you again.
auex 
Platinum - Posts: 5,041
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: December 23, 2002
Location: Arizona, United States
Posted: January 08, 2003 at 10:23 PM / IP Logged  
I checked the stats out and the amp is stable at 2 ohms so I would do the wiring of the voice coils in series and then run the subs in parrallel for a load of 2.6.  As for adding a second amp to three subs I personally wouldn't do it, it would oddball the resistances and one of the subs would end up getting a lot more power than the other two and the subs would end up fight each other, so to speak ( the amplification difference would end up causing cancelation of frequencies because of the difference in power). If you wanted to add another sub and then the other amp then it would work a lot better but I would try it the way I mentioned earlier and see if that sounds good.
Certified Security Specialist
Always check info with a digital multimeter.
I promise to be good.
Tell Darwin I sent you.
I've been sick lately, sorry I won't be on much.
mgeorge 
Member - Posts: 3
Member spacespace
Joined: January 08, 2003
Location: United States
Posted: January 08, 2003 at 10:33 PM / IP Logged  

Thank you for replying again. In one response you say voice coils in series and subs in parallel, in the other you say the oposite.  Please conferm which will produce 2.6.  Also what would happen if you only connect one of the voice coils (just currious). Thank you for all your help.

Michael


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Sunday, May 19, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer