the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

94 fullsize blazer , viper 791xv hatch

Home / the12volt's Install Bay / Car Security and Convenience / 94 fullsize blazer , viper 791xv hatch (Topic Closed Topic Closed)
Welcome Guest :)

Post ReplyPost New Topic
< Prev Topic Next Topic >
gmoney43080 
Member - Posts: 11
Member spacespace
Joined: December 12, 2009
Location: Maryland, United States
Posted: December 13, 2009 at 8:00 PM / IP Logged  

im sorry im new here but i have a 791xv viper alarm and a 94 fullsize chevy blazer. i want to know how to connect the alarm to open the rear hatch with the remote, do i need a relay and if so can you tell me how or send me a diagram

i am an idiot 
Platinum - Posts: 13,672
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: December 13, 2009 at 9:11 PM / IP Logged  
94 fullsize blazer , viper 791xv hatch -- posted image.Trnk ReleaseBROWN(+)

RELEASE SWITCH IN DASH

Yes you will need a relay. Wire it as follows.

Terminal 85 connects to the output wire of your alarm.
Terminals 86 and 30 connect to a constant power source.  Fused at 10 amps.
Terminal 87 connects to the brown wire at the release switch.

gmoney43080 
Member - Posts: 11
Member spacespace
Joined: December 12, 2009
Location: Maryland, United States
Posted: December 14, 2009 at 7:30 PM / IP Logged  
Ok now I'm having a bigger problem, NOW I hooked the relay up how you said to hook it up and it didn't work so I thought I needed to program my remote for some odd reason (my first remote is the one with the screen). and now I can't remote start my car it tries but it stops too soon to start it and my doors won't lock or unlock, please help me even with my second remote, but on my second remote I can arm and disarm (but still can't unlock or lock it) it but on my first remote I can only arm it, it won't disarm, if the alarm goes off I have to press the arm button again to stop it.
t&t tech 
Platinum - Posts: 2,608
Platinum spacespace
Joined: October 05, 2008
Location: Trinidad and Tobago
Posted: December 14, 2009 at 8:09 PM / IP Logged  

Just re-program the remotes, STEPS-

1) open door

2) Turn ignition on

3) press and release valet switch twice holding on second press, wait for a single chirp from the siren, then press lock button on remote! A long chirp indicates success!

commit your way to jehovah and he will act in your behalf. psalms 37:5
gmoney43080 
Member - Posts: 11
Member spacespace
Joined: December 12, 2009
Location: Maryland, United States
Posted: December 14, 2009 at 8:43 PM / IP Logged  
Ok I'm about to try that now
gmoney43080 
Member - Posts: 11
Member spacespace
Joined: December 12, 2009
Location: Maryland, United States
Posted: December 14, 2009 at 10:37 PM / IP Logged  
nope that didnt work either, it made all the sounds you said it would make but still wont unlock the doors or hatch or start the truck, it will try for a half of a second and stop
i am an idiot 
Platinum - Posts: 13,672
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: December 14, 2009 at 11:21 PM / IP Logged  
Where did you get power for the relay?  Have you checked for blown fuses in the vehicles fuse boxes?  Did you fuse the power wire for the relay?
gmoney43080 
Member - Posts: 11
Member spacespace
Joined: December 12, 2009
Location: Maryland, United States
Posted: December 14, 2009 at 11:54 PM / IP Logged  
i didnt think to check for blown fuse in the box but i checked the fuses associated with the viper because i went off of the wires connected to the door lock relays for power but the locks was still working fine until i started messing with the valet button, and i also accidentally followed the process to program the viper with the computer thing (bitwriter) if that can help you help me in anyway, i was pressing button could it have anything to do with this?                 < lang=JA size=2 face=AdobePiStd>< lang=JA size=2 face=AdobePiStd>

¡ < size=2 face=OfficinaSans-Book>< size=2 face=OfficinaSans-Book>Pressing one time: The siren chirps once. The system is armed.

< lang=JA size=2 face=AdobePiStd>< lang=JA size=2 face=AdobePiStd>

¡ < size=2 face=OfficinaSans-Book>< size=2 face=OfficinaSans-Book>Pressing a second time within five seconds: The siren chirps twice followed by a long chirp. Zone

Two is now bypassed.

< lang=JA size=2 face=AdobePiStd>< lang=JA size=2 face=AdobePiStd>

¡ < size=2 face=OfficinaSans-Book>< size=2 face=OfficinaSans-Book>Pressing a third time within five seconds: The siren chirps three times followed by a long chirp. Zone

Four is now bypassed.

< lang=JA size=2 face=AdobePiStd>< lang=JA size=2 face=AdobePiStd>

¡ < size=2 face=OfficinaSans-Book>< size=2 face=OfficinaSans-Book>Pressing a fourth time within five seconds: The siren chirps four times followed by a long chirp.

Zones Two and Four are now bypassed.

< lang=JA size=2 face=AdobePiStd>< lang=JA size=2 face=AdobePiStd>

¡ < size=2 face=OfficinaSans-Book>< size=2 face=OfficinaSans-Book>Pressing a fifth time within five seconds: The siren chirps five times followed by a long chirp. All

input zones, except the ignition, are now bypassed                                                                                                                                            OR THIS                    < size=2 face=OfficinaSans-Book>< size=2 face=OfficinaSans-Book>

Channels Two through Nine are used to assign the arm, disarm and panic functions

to separate buttons on the remote control. Teaching a button to Channel Two erases all information about

that remote from memory. Any auxiliary functions that are desired will have to be reprogrammed. Similarly, if the

remote is set up to use the separate arm, disarm and panic channels and a button from that remote is entered

into Channel Two, the remote will be erased from memory, and the system will only recognize the button that

was entered into Channel Two.

gmoney43080 
Member - Posts: 11
Member spacespace
Joined: December 12, 2009
Location: Maryland, United States
Posted: December 15, 2009 at 6:14 AM / IP Logged  
I forgot to mention if I start thr truck using the key, if I press the star button two times to take my keys with me the lights will blink but the doors won't unlock and when I turn the ignition of the truck cuts off but t seems like its on (meaning the lights are on and if I try to put the keys back in to start it, it won't as if the anti grind mode is on so I have to press the brake to shut it of and then start it

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Sunday, May 12, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved • Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer