2005 malibu maxx 2way car alarm

hello, and thank you for letting me use your forum... i'm hoping for a quick response as i need to get my wifes car put back together as she says it has been long enough. To begin I have a spy 5000m 2 way car alarm I purchased online about 6 months ago. I am posting here as I can not figure out the engrish instructions. I contacted the seller he said sorry he don't offer tech support and good luck. Can not contact the manufacturer as it is in Singapore. And no alarm guys around or near where I live will touch it. They rather sell me something else that they know how to install and i cannot spend money on new system and i wouldn't feel comfortable pawning this system off on someone else lol. ok theese are the wires for the alarm manual as follows: eighteen terminal plug: aux channel 3 neg output(300mA) / yellow-blue aux channel 1 neg output(300mA)/ yellow-black parking brake neg input / orange-violet door neg input / blue-black hood neg input / orange-grey / R1 engine temp sensor carbody(-)     / black trunk neg input/ orange-white door pos input / blue red tach wire      / grey-black pos output siren/ grey engine lock neg output(300mA)/ black-white pos output marker lights (7a)/ green-yellow pos output marker lights (7a (7a)/ green-black 12v power sully 15 amp fuse/ red aux channel 4 neg output (300mA) / blue CAS bypass neg output(300mA) black-red CAS state neg output(300mA) black-yellow aux channel 2 neg output (300mA)/ yellow-red Six Terminal engine starting plug connection: ignition starting pos output no 1 / yellow ignition starting pos output no 2 / green starter pos input (to 50/1 ignition lock contact)/black-white 12v power supply (30 amp fuse) / red starter activation pos output ( to starter)/black-yellow CAS enabling pos output/ blue Connection of six terminal central lock connector: NO locking relay contact NO / green-white NC locking relay contact / green-black NC unlocking relay contact / blue-black locking relay bridging contact / green unlocking relay bridging contact / blue NO unlocking relay contact / blue-white Now I have the XK06-pkg7 install guide found here: http://www.bypasskit.com/manuals/420_XK06180_H00_S00_D00_I_EN.pdf ANd my car diagram found here: http://www.commandocaralarms.com/wiring/2004-2007/chevrolet/malibumaxx/479.html    or here https://www.the12volt.com/installbay/forum_posts.asp~TID~85886 I have been using this info and i get no where.. SO i completely pulled it out and now would like if someone would be kind enough to help me out. Just tell me what wire goes where PLEASE and THANKYOU your forum friend, WIlliam

The first thing you need to do is to relate what you've written with respect to your alarm next to the instructions for your vehicle. If you look up your vehicle on the vehicle wiring section you will find a better description. Write what you think goes where. We might be able to take it from there.

Thank you for a reply I noted the info next to wire below

madmaxx2005 wrote: hello, and thank you for letting me use your forum... i'm hoping for a quick response as i need to get my wifes car put back together as she says it has been long enough. To begin I have a spy 5000m 2 way car alarm I purchased online about 6 months ago. I am posting here as I can not figure out the engrish instructions. I contacted the seller he said sorry he don't offer tech support and good luck. Can not contact the manufacturer as it is in Singapore. And no alarm guys around or near where I live will touch it. They rather sell me something else that they know how to install and i cannot spend money on new system and i wouldn't feel comfortable pawning this system off on someone else lol. ok theese are the wires for the alarm manual as follows: eighteen terminal plug: aux channel 3 neg output(300mA) / yellow-blue ** dont use aux channel 1 neg output(300mA)/ yellow-black ** dont use parking brake neg input / orange-violet    ** lt blue wire on bcm 1 door neg input / blue-black      ** i think use this one diode isolate hood neg input / orange-grey ** car has factory hood pin / R1 engine temp sensor   **dont know carbody(-)     / black      ** ground trunk neg input/ orange-white ** car has trunk pin too door pos input / blue red   ** dont use tach wire / grey-black ***Through firewall to injector pos output siren/ grey   *** through firewall to siren or to horn wire engine lock neg output(300mA)/ black-white ** dont know pos output marker lights (7a)/ green-yellow   ** to parkight pos wire pos output marker lights (7a (7a)/ green-black ** to parkight pos wire 12v power sully 15 amp fuse/ red   12v contant red on bcm 3 aux channel 4 neg output (300mA) / blue    ** dont know/dont use CAS bypass neg output(300mA) black-red **** dont know CAS state neg output(300mA) black-yellow **** dont know aux channel 2 neg output (300mA)/ yellow-red Dont know/dont use Six Terminal engine starting plug connection: ignition starting pos output no 1 / yellow   **pink wire bcm ignition starting pos output no 2 / green *** dont know starter pos input (to 50/1 ignition lock contact)/black-white****dont know 12v power supply (30 amp fuse) / red ***red bcm starter activation pos output ( to starter)/black-yellow***dont know CAS enabling pos output/ blue *** dont know Connection of six terminal central lock connector: NO locking relay contact NO / green-white ** dont know NC locking relay contact / green-black   ** dont know NC unlocking relay contact / blue-black ** dont know locking relay bridging contact / green   ** dont know unlocking relay bridging contact / blue ** dont know NO unlocking relay contact / blue-white ** dont know Now I have the XK06-pkg7 install guide found here: http://www.bypasskit.com/manuals/420_XK06180_H00_S00_D00_I_EN.pdf ANd my car diagram found here: http://www.commandocaralarms.com/wiring/2004-2007/chevrolet/malibumaxx/479.html    or here https://www.the12volt.com/installbay/forum_posts.asp~TID~85886 I have been using this info and i get no where.. SO i completely pulled it out and now would like if someone would be kind enough to help me out. Just tell me what wire goes where PLEASE and THANKYOU your forum friend, WIlliam

Good Luck with this one.  Need better wire descriptions for this units install. 

Here is my best guess.

aux channel 3 neg output(300mA) / yellow-blue   NU

aux channel 1 neg output(300mA)/ yellow-black   Program for Trunk Release  BROWN / WHITE (-) @ TRUNK RELEASE SWITCH or BCM, C1, 72-PIN GRAY PLUG, PIN 71parking brake neg input / orange-violet                Parking Brake  LIGHT BLUE  (-)  BLUE PLUG BCM door neg input / blue-black          GRAY/BLACK (-)(DRIVERS) and TAN/WHITE (-)(PASSENGERS)                Diode isolate all 4 into one       LIGHT BLUE/BLACK  (-) and LIGHT GREEN/ BLACK  (-) all @ BLUE PLUG IN BCM hood neg input / orange-grey     Hood Pin supplied with kit/ R1 engine temp sensor               ???carbody(-)     / black         Chassis Groundtrunk neg input/ orange-white       Trunk Trigger  ORANGE / BLACK  (-)  BLUE PLUG IN BCM door pos input / blue red NUtach wire      / grey-black               Any wire NOT PINK (AC)  @ ANY FUEL-INJECTOR pos output siren/ grey     To supplied sirenengine lock neg output(300mA)/ black-white   ??? Starter Kill ????  NUpos output marker lights (7a)/ green-yellow       BROWN (+)  IN DRIVERS KICK PANEL or BCM, C3, 42-PIN RED PLUG, PIN A7pos output marker lights (7a (7a)/ green-black              NU 12v power sully 15 amp fuse/ red            +12V constant RED / BLACK (+)   @ BCM, C3 RED 41-PIN PLUG, PIN D1aux channel 4 neg output (300mA) / blue            NUCAS bypass neg output(300mA) black-red         To XK06 Brown wireCAS state neg output(300mA) black-yellow        NUaux channel 2 neg output (300mA)/ yellow-red      NU  

Six Terminal engine starting plug connection: One of these should be an Accessory Output

ignition starting pos output no 1 / yellow                      PINK (+)  @ IGNITION SWITCH HARNESS or BCM, C4 LT. GRAY, 68-PIN PLUG, PIN D3,

ignition starting pos output no 2 / green         ??? Is this output selectable for Accessorystarter pos input (to 50/1 ignition lock contact)/black-white  ???  +12V constant RED / BLACK (+)   @ BCM, C3 RED 41-PIN PLUG, PIN D112v power supply (30 amp fuse) / red            +12V constant RED / BLACK (+)   @ BCM, C3 RED 41-PIN PLUG, PIN D1starter activation pos output ( to starter)/black-yellow             To XK06 OrangeCAS enabling pos output/ blue    ??? BROWN (+) @ IGNITION SWITCH HARNESS or BCM, C4 LT. GRAY, 68-PIN PLUG, PIN C8

    Assuming this is the Accessory output

Connection of six terminal central lock connector:   One wire (-) resistance system.

NO locking relay contact NO / green-white           Chassis ground

NC locking relay contact / green-black NC unlocking relay contact / blue-black locking relay bridging contact / green        white (-)  driver kick or BCM, gray 72 pin plug (C1), pin 66 unlocking relay bridging contact / blue      white (-)  driver kick or BCM, gray 72 pin plug (C1), pin 66 NO unlocking relay contact / blue-white   thru 1.5K ohm resistor to chassis ground

Soldering is fun!

oh and the bypass kit dont know where the brown ground when running wire would go, i believe i hook the other correctly

i will try this will post back if all is ok. Thank you so much for a response

Might help if you post a picture of the 6 Pin connector.  Seeing it, the gauge of the wires and the location of any fuses would be of assistance.Soldering is fun!

Theese setting worked!!!!!! woot and big thanks to you!!!! my wife is so happy, and says BIG /huggs

kreg357 wrote: Good Luck with this one.  Need better wire descriptions for this units install.  Here is my best guess. aux channel 3 neg output(300mA) / yellow-blue NU aux channel 1 neg output(300mA)/ yellow-black Program for Trunk Release  BROWN / WHITE (-) @ TRUNK RELEASE SWITCH or BCM, C1, 72-PIN GRAY PLUG, PIN 71 parking brake neg input / orange-violet Parking Brake  LIGHT BLUE  (-)  BLUE PLUG BCM door neg input / blue-black       GRAY/BLACK (-)(DRIVERS) and TAN/WHITE (-)(PASSENGERS)              Diode isolate all 4 into one       LIGHT BLUE/BLACK  (-) and LIGHT GREEN/ BLACK  (-) all @ BLUE PLUG IN BCM hood neg input / orange-grey  Hood Pin supplied with kit / R1 engine temp sensor                     ??? carbody(-)     / black                Chassis Ground trunk neg input/ orange-white     Trunk Trigger  ORANGE / BLACK  (-)  BLUE PLUG IN BCM door pos input / blue red       NU tach wire      / grey-black        Any wire NOT PINK (AC)  @ ANY FUEL-INJECTOR pos output siren/ grey To supplied siren engine lock neg output(300mA)/ black-white    ??? Starter Kill ????  NU pos output marker lights (7a)/ green-yellow       BROWN (+)  IN DRIVERS KICK PANEL or BCM, C3, 42-PIN RED PLUG, PIN A7 pos output marker lights (7a (7a)/ green-black  NU 12v power sully 15 amp fuse/ red       +12V constant RED / BLACK (+)   @ BCM, C3 RED 41-PIN PLUG, PIN D1 aux channel 4 neg output (300mA) / blue        NU CAS bypass neg output(300mA) black-red      To XK06 Brown wire CAS state neg output(300mA) black-yellow        NU aux channel 2 neg output (300mA)/ yellow-red    NU Six Terminal engine starting plug connection: One of these should be an Accessory Output ignition starting pos output no 1 / yellow                   PINK (+)  @ IGNITION SWITCH HARNESS or BCM, C4 LT. GRAY, 68-PIN PLUG, PIN D3, ignition starting pos output no 2 / green       ??? Is this output selectable for Accessory starter pos input (to 50/1 ignition lock contact)/black-white  ???  +12V constant RED / BLACK (+)   @ BCM, C3 RED 41-PIN PLUG, PIN D1 12v power supply (30 amp fuse) / red       +12V constant RED / BLACK (+)   @ BCM, C3 RED 41-PIN PLUG, PIN D1 starter activation pos output ( to starter)/black-yellow             To XK06 Orange CAS enabling pos output/ blue       ??? BROWN (+) @ IGNITION SWITCH HARNESS or BCM, C4 LT. GRAY, 68-PIN PLUG, PIN C8   Assuming this is the Accessory output Connection of six terminal central lock connector:   One wire (-) resistance system. NO locking relay contact NO / green-white        Chassis ground NC locking relay contact / green-black NC unlocking relay contact / blue-black locking relay bridging contact / green      white (-)  driver kick or BCM, gray 72 pin plug (C1), pin 66 unlocking relay bridging contact / blue    white (-)  driver kick or BCM, gray 72 pin plug (C1), pin 66 NO unlocking relay contact / blue-white   thru 1.5K ohm resistor to chassis ground

Cool. A warm car on a cold morning is a wonderful thing.  A happy wife is even better.   Soldering is fun!

thick gauge wire fuse farthest from conector