viper 3002 for 01 tribute

i have a viper 3002 and im installing it on 01 mazda tribute and after i get this done i will install excaliber rs-130-dp and a 556uw by pass my questions for the viper alarm are lightGREEN/ black says it goes to neg factory disarm output do i run this wire directly to that factory disarm wire? next question is on the viper unit it has a neg second unlock do i use this wire? on the orginal keyless entry i have to hit unlock 2x to unlock passenger door. the third question is the unlock/lock door harness i know i use a 1000k resistor but a diagram would help alot. and for the remote start what wire on the viper unit do i use to activate it? thanks for any help it is greatly appreciated.wes5314

wes5314 wrote: i have a viper 3002 and im installing it on 01 mazda tribute and after i get this done i will install excaliber rs-130-dp and a 556uw by pass my questions for the viper alarm are lightGREEN/ black says it goes to neg factory disarm output do i run this wire directly to that factory disarm wire?

Yes

wes5314 wrote: next question is on the viper unit it has a neg second unlock do i use this wire? on the orginal keyless entry i have to hit unlock 2x to unlock passenger door.

If you want to maintain the Drivers Priorty Unlock then yes.

wes5314 wrote: the third question is the unlock/lock door harness i know i use a 1000k resistor but a diagram would help alot.

Audiovox Doorlocks/Windows        WIRE COLOR POLARITY LOCATION Power Unlock ORANGE / BLACK (-) DRIVERS KICK PANEL DOUBLE PUSLE FOR UNLOCK    MUST USE A RESISTOR FOR INTEGRATION    PowerLock YELLOW/RED (-) DRIVERS KICK PANEL, 1K OHM RESISTOR.    USE A 1KOHM RESISTOR Directwire Power Lock pink/white   - DKP or 26 pin plug @ GEM Notes: Lock requires a negative trigger thru a 1,000 ohm resistor. Unlock is a negative trigger. Must use relay on both. The GEM (generic electronic module) is behind the center console on the floor. Pull off the black panel to the right of the gas pedal, there will be carpet covering it. The plugs face the driver side of the vehicle. Power Unlock same wire    Or a 451M for the interface.

wes5314 wrote: and for the remote start what wire on the viper unit do i use to activate it? thanks for any help it is greatly appreciated.

WHITE/ Blue Wire - Remote Start Activation (-) Input to the channel output on the viper you want to use to activate the remote start.

And here's the how to diagram including colour codes you will need a 4 or 5* pin relay Bosch/Tycho and a 1N4004 diode on the second unlock wire to 85 on the relay:- mazda_priority_unlock.bmp * If 5 pin (more readily available), just ignore pin 87a.

what does the turquoise on the 85 relay hook to on the alarm i have all those colors but that one?wes5314

I think it's supposed to be Ground, as I not to familiar with the 3203 units.

I only have violet blue/black, brown /black, violet/black, GREEN/ black white /black but no blue on the lock harness on the alarm sorry if im misunderstanding just am not seeing a blue wes5314

lurch228 wrote: I think it's supposed to be Ground, as I not to familiar with the 3203 units.

Sorry corrected myself. Standard relay wiring is 85 ground, 86 positive, 30&87a NC, 87 NO

Actually it's supposed to be light blue second lock output.

And that second relay MAY not be needed.

I stand corrected howie. As I stated, never used the stand alone alarms with internal relays. But as the OP stated he dosen't have a light blue 2nd unlock so he can't have a 3002 can he? Or are there two date code revisions for the 3002?

wes5314 wrote: I only have violet blue/black, brown /black, violet/black, GREEN/ black white /black but no blue on the lock harness on the alarm sorry if im misunderstanding just am not seeing a blue