This will be all W2W, sorry. D2D doesn't save many wires...
OK. Here goes...
First the XK01 w/TOYDL ( door locks )
XK01 Viper
Green Lock In Green Lock Out
Blue Unlock In Blue Unlock Out
Red +12V Red +12V
Black Chassis Ground Black Chassis Ground
Violet Data wire to Sequoia WHITE/ Blue in DPK
Next the XK05 w/PKT2 transponder bypass
XK05 Viper
Brown GWR Dark Blue (-) Status Output
Red +12V Red +12V
Black Chassis Ground Black Chassis Ground
Blue Ignition In Pink thick IGN1
Green, Violet, Violet/White and Orange to Sequoia as per diagram & install guide
Viper 4706V
H/1 RED (+)12VDC CONSTANT INPUT WHITE/ red (25A) (+) @ ignition switch
H/2 BLACK (-) CHASSIS GROUND Chassis Ground with XK01 & XK05 Black
H/3 BROWN (-) 200mA HORN HONK OUTPUT BLACK / YELLOW (-) @ horn switch
H/4 WHITE/ BROWN LIGHT PIN 87a Not Used
H/5 WHITE PIN 30 of LIGHT FLASH RELAY green (-) @ headlight switch *set jumper/fuse to (-)
H/6 ORANGE 500 mA GWA OUTPUT Not Used
1 BLUE 500mA (-) UNLOCK OUTPUT to XK01
2 EMPTY NOT USED
3 GREEN 500mA (-) LOCK OUTPUT to XK01
1 RED / BLACK (+) 12VDC CONSTANT WHITE/ blue (25A) + @ ignition switch
2 PINK/BLACK (+) FLEX RELAY INPUT 87A not used
3 PINK/WHITE (+) IGNITION 2 / FLEX OUTPUT BLACK/ red + @ ignition switch
4 RED (+) 12VDC CONSTANT INPUT WHITE/ red (25A) + @ ignition switch
5 VIOLET (+) STARTER OUTPUT BLACK/ white + ignition switch
6 ORANGE (+) ACCESSORY OUTPUT pink + ignition switch
7 RED / WHITE (+) 12VDC CONSTANT INPUT WHITE/ blue (25A) + @ ignition switch
8 PINK (+) IGNITION 1 INPUT/OUTPUT BLACK/ red + @ ignition switch plus XK05 Blue
1 PINK/WHITE (-) 200mA Ignition 2/Flex OUTPUT Not Used
2 BLUE/WHITE (-) 200mA 2ND STATUS /REAR DEFOG Not Used
3 RED / WHITE (-) 200mA TRUNK RELEASE OUTPUT Not Used
4 BLACK / YELLOW (-) 200mA DOME LIGHT OUTPUT Not Used
5 DARK BLUE (-) 200mA STATUS OUTPUT To XK05 Brown
6 WHITE/ BLACK (-) 200mA AUX 3 OUTPUT Not Used
7 WHITE/ VIOLET (-) 200mA AUX 1 OUTPUT Not Used
8 ORANGE / BLACK (-) 200mA AUX 4 OUTPUT Not Used
9 GRAY (-) HOOD PIN INPUT (NC OR NO) to kit supplied hood pin
10 BLUE* FACTORY HORN INPUT Not Used
11 WHITE/ BLUE ACTIVATION INPUT Not Used
12 VIOLET/WHITE** TACHOMETER INPUT YELLOW /GREEN ac @ cluster, wht 40 pin plg, pin 23
13 BLACK/ WHITE*** (-) NEUTRAL SAFETY Chassis Ground
14 GREEN/ BLACK (-) 200mA FACTORY ALARM DISARM Not Used
15 GREEN** (-) DOOR INPUT Not Used
16 EMPTY ------------------------------------
17 PINK (-) 200mA IGNITION 1 OUTPUT Not Used
18 VIOLET** (+) DOOR INPUT Not Used
19 VIOLET/BLACK (-) 200mA AUX 2 OUTPUT Not Used
20 BROWN (+) BRAKE SHUTDOWN INPUT GREEN / WHITE (+) @ driver kick
21 VIOLET / YELLOW (-) 200mA STARTER OUTPUT Not Used
22 GRAY/BLACK (-) DIESEL WAIT TO START INPUT Not Used
23 ORANGE (-) 200mA ACCESSORY OUTPUT Not Used
24 GREEN / WHITE (-) 200mA FACTORY ALARM ARM Not Used
You should locate, test and verify all wires with a DMM...
Soldering is fun!