92 mercury sable alarm

Home / the12volt's Install Bay / Car Security and Convenience / 92 mercury sable alarm (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

mogmit

Member - Posts: 12

Joined: November 07, 2004

Location: Canada

Posted: November 07, 2004 at 7:01 PM / IP Logged

need wiring diagram for a 1992 mecury sable to install car starter

mo12v

Platinum - Nominee - Posts: 2,748

This member consistently provides reliable information

Joined: September 30, 2003

Location: Afghanistan

Posted: November 07, 2004 at 7:07 PM / IP Logged

Constant 12 volts	YELLOW (5 TOTAL)	IGNITION SWITCH HARNESS
Ignition 12 volts	RED / LIGHT GREEN	IGNITION SWITCH HARNESS
Starter	WHITE/ PINK	IGNITION SWITCH HARNESS
Dome Light	BLACK/ LIGHT BLUE (+)	DRIVER KICK PANEL OR AT PIN SWITCH
Trunk Pin Switch	N/A
Parking Lamp	BROWN (+)	HEADLIGHT SWITCH OR DRIVER KICK PANEL
Power Lock	PINK / YELLOW	DRIVER KICK
Power Unlock	PINK/LIGHT GREEN	PANEL *

* With OEM Keyless Entry Negative Pulse Door Locks

Without OEM Keyless Entry Reversal Rest At Ground Door Locks

. It Is Common For Lock & Unlock Wire Colors To Reverse.

Accessories
Window Up	D\ YEL P\ WHT/YEL D\ YEL/BLU P\ GRY/ORG @ MAIN SWITCH
Window Down	F/ WHT/BLK F/ TAN/BLU R/ YEL/BLK R/ RED / BLK
Ign Key Warn	BLACK/ PINK (-)	STEERING COLUMN HARNESS OR CHIME MOD.
Trunk Release	GRAY/RED (+) WAGON OR	PINK / YELLOW (+) SEDAN WITH KEYLESS
OEM Horn	YELLOW/LIGHT GREEN (-)	RELAY BEHIND CENTER OF DASH ON BRACK.
Headlights	RED / YELLOW (+)	HEADLIGHT SWITCH OR BEAM SELECT SW.
OEM Alarm Arm	N/A
OEM Alarm Disarm	N/A

Reversal Rest At Ground Power Window Circuit .-

Positive Pulse trunk Release

Remote Start
Tach Signal	TAN / YELLOW	AT DISTRIBUTOR OR IGN. CONTROL MOD. *
Ignition #2	GRAY / YELLOW (2)	IGNITION SWITCH HARNESS **
Ignition #3	GRAY / YELLOW	IGNITION SWITCH HARNESS **
Accessory	BLACK/ LIGHT GREEN	IGNITION SWITCH HARNESS **
Neutral Safety	NOT GROUNDING TYPE -	OEM SWITCH OPENS STARTER CIRCUIT
Brake Light	RED / LIGHT GREEN	SWITCH ON BRACKET ABOVE BRAKE PEDAL
Reverse Light	BLACK/ PINK	AT SWITCH ON REAR OF TRANSAXLE
Rear Window Defrost	N/A

* 3.0L Tach Wire Located At Distributor, 3.8L At Ignition Control Module On Passenger Firewall. 3.0l Flex Fuel- WHITE/ PINK At Ignition Control Module On Passenger Side Of Engine.

** Ignition Switch Layout: Starter...................WHITE/ PINK. Ignition #1...............RED / L GREEN (Primary Ignition). Ignition #2...............GRAY / YELLOW (2) (Heat/Ac). * Ignition #3...............GRAY / YELLOW (Keeps "ABS" Light Off). Accessory.................BLACK/ L GREEN (Heat/Ac Controls). * 2 Of The 3 GRAY / YELLOW Wires Listed Are The Same Circuit.

Don't Learn from Others Mistakes

You Might Be the One That Knows.

mogmit

Member - Posts: 12

Joined: November 07, 2004

Location: Canada

Posted: November 10, 2004 at 11:13 PM / IP Logged

BLACK This is the (-) Status Out wire (ground when running). It provides you with a (-) 200mA output as soon as the remote start is activated

ORANGE This is the rearm wire. It provides you with a (-) pulse when armed, after remote start and then again after remote start shuts down.

ORANGE / WHITE This is the disarm wire. It provides you with a (-) pulse when disarmed and before remote start.

Where do these wires go in a 92 merc sable??????

draasch

Gold - Posts: 2,172

Joined: February 07, 2003

Location: Florida, United States

Posted: November 11, 2004 at 6:54 AM / IP Logged

on that year car, you wont need a by-pass and it doesnt come with a factory alarm....you shouldnt need those wires....

Good Luck

David

Ace Security

813-376-9778

Tampa

Donate to the 12volt

mogmit

Member - Posts: 12

Joined: November 07, 2004

Location: Canada

Posted: November 11, 2004 at 4:37 PM / IP Logged

RED / White Wire is used as the (+) Constant power input for the Starter and 2nd ignition.

Would I just hook this up to the 2nd ignition??

mogmit

Member - Posts: 12

Joined: November 07, 2004

Location: Canada

Posted: November 11, 2004 at 10:19 PM / IP Logged

RED / WHITE Wire is used as the (+) Constant power input for the Starter and 2nd ignition.

Would I just hook this up to the 2nd ignition???

BLUE Wire will power (+)2nd starter, (+)2nd Accessory or (+)2nd Ignition depending on the jumper selection.

Does this wire even need to be connected??

This is an Arctic Start car starter going into a 1992 mercury sable and this book only tells you what the wire does not where it goes, I have gotten everything else now except for these wires.

Any help would be greatly appreciated!

jrilla

Gold - Posts: 1,498

This member has made a donation to the12volt.com. Click here for more info.

Joined: November 19, 2002

Location: North Dakota, United States

Posted: November 11, 2004 at 10:48 PM / IP Logged

The RED / White must go to 12v+ constant in the ignition harness which is yellow. You may have three to choose from, any will do. If you have more than one power input wire like this (as most starter units do) then grab one yellow for each.

I show 2 accessory wires on that vehicle so you should grab both with your acc 1 and the Blue wire you asked about: Gray / YELLOW and BLACK/ green are the two I show. Be sure to set the jumper on the correct pins (accessory position)

J Rilla

Owner/Installer

jrilla

Gold - Posts: 1,498

Joined: November 19, 2002

Location: North Dakota, United States

Posted: November 11, 2004 at 10:57 PM / IP Logged

Now that I read your question aagin: I am sure you have another wire just like the RED / White wire and it likely says something like: Wire is used as the (+) constant power input for the accessory and selectable output wires. There is also likely a 30 amp fuse on each of those wires (the RED / White and the other I am referring to)

I understand how confusing things can be the first time around since I had a terrible wire diagram and an even worse install manual on my first install and i had everything backwards until i called tech support and they straightened me out right quick. Sometimes re-reading every word carefully helps, like on that RED / White wire it states that it is an input that supplies power to 2 of the most critical outputs that a remote starter has. So Input and Constant mean you need to connect this wire to the battery (but since the ignition harness has a wire that is eventually connected to the battery then you can grab the battery power there).

Be sure to ask any questions you have. Always test wires before you connect to them. Solder and tape well all connections.

Good luck.

J Rilla

Owner/Installer

mogmit

Member - Posts: 12

Joined: November 07, 2004

Location: Canada

Posted: November 11, 2004 at 10:58 PM / IP Logged

the accessory is BLACK/ light green in the ignition switch harness where and what colour would the second accessory be??

jrilla

Gold - Posts: 1,498

Joined: November 19, 2002

Location: North Dakota, United States

Posted: November 11, 2004 at 10:59 PM / IP Logged

I show Gray/Yelloow as Acc 1 and BLACK/ Green as Acc 2.

Ignition is RED / Lt.Green and

Starter is WHITE/ Pink

J Rilla

Owner/Installer

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.