2001 2500hd

Home / the12volt's Install Bay / Car Security and Convenience / 2001 2500hd (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

pacinfool

Member - Posts: 19

Joined: November 30, 2002

Location: United States

Posted: December 02, 2002 at 3:19 PM / IP Logged

Hey I had the question about the 2001 2500HD, I didn't have the second ignition wire hooked up, so I hooked it up to pin 2 through a relay, and now I have no power to several things on the dash(4x4 switch, cruise, wipers, heater fan, etc.) It also blew the fuses for the remote starter. Any ideas what I did wrong?Thanks

Ryan

securinu

Silver - Posts: 772

This member has made a donation to the12volt.com. Click here for more info.

Joined: September 15, 2002

Location: United States

Posted: December 02, 2002 at 4:15 PM / IP Logged

how did you hook up the relay give detail of pins connections and also are you sure you got the white ignition 12+ wire and not something else???

pacinfool

Member - Posts: 19

Joined: November 30, 2002

Location: United States

Posted: December 02, 2002 at 6:08 PM / IP Logged

I hooked up the relay as follows:pin 85 to pin 2 on J2 plug, pin 86 to ground, pin 87 to fused constant 12V , pin 30 to second ignition wire(white 12V small wire from igition harness). It's like I lost most accessory power.

Ryan

securinu

Silver - Posts: 772

Joined: September 15, 2002

Location: United States

Posted: December 02, 2002 at 6:16 PM / IP Logged

well it sounds like the relay coil has 2 negative signals which it will not energize to open up is the j2 pin 2 a negative ouput if so then pin 86 on the relay needs to go to 12 volts + not ( - ) also the white wire is approx 14 guage and is right next to the starter wire in the factory connector .

pacinfool

Member - Posts: 19

Joined: November 30, 2002

Location: United States

Posted: December 02, 2002 at 6:20 PM / IP Logged

J2 pin is + output

Ryan

securinu

Silver - Posts: 772

Joined: September 15, 2002

Location: United States

Posted: December 02, 2002 at 6:26 PM / IP Logged

ok so that should work. but you can try to going to 12 v+ and ground with the relay and see if also did you check the wire to make sure it test properly???

pacinfool

Member - Posts: 19

Joined: November 30, 2002

Location: United States

Posted: December 03, 2002 at 7:35 AM / IP Logged

When I tested the ignition wires, I have no power on the brown accessory wire or the orange hvac1 wire. Help!!!!!!!

Ryan

pacinfool

Member - Posts: 19

Joined: November 30, 2002

Location: United States

Posted: December 03, 2002 at 10:09 AM / IP Logged

Here is some more info- when both fuses for constant 12v are in J1 plug and the key is in the "run" position everything works, but the starter runs. When I take one of the fuses out the gauges work but still no heat or 4x4 switch, when I take the other fuse out the horn goes off with key in "run" position. Any ideas?

Ryan

Velocity Motors

Moderator - Posts: 12,488

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: December 03, 2002 at 10:27 AM / IP Logged

Hey Ryan, can you please enter all the wires that you attached from the CS unit to the colors on the truck ? This way we can trouble shoot better to see if there was a connection that you used wrong or if you require additional relays or diodes.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

pacinfool

Member - Posts: 19

Joined: November 30, 2002

Location: United States

Posted: December 03, 2002 at 10:39 AM / IP Logged

I'm at work now, but I will do that tonight, probably around 8:30 or 9:00. Thanks for the help guys.

Ryan

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.