autopage 860 wont shut off

Home / the12volt's Install Bay / Car Security and Convenience / autopage 860 wont shut off (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

tnez2

Member - Posts: 26

Joined: March 19, 2006

Location: United States

Posted: December 03, 2006 at 10:41 AM / IP Logged

Help i put in this alarm replaced a older alarm, it starts but wont shut off even if i push the break or open the hood. it on a 2001 ford ranger. if i start it with the key and shut the key off it still runs, the only way to shut it off is to pull the fuses on the alarm. pleas help

captainzab

Silver - Posts: 606

This member has made a donation to the12volt.com. Click here for more info.

Joined: February 09, 2005

Location: United States

Posted: December 03, 2006 at 11:56 AM / IP Logged

Someone didnt hook up the brake or hood wire then.

If they did, then they got the wrong wire. Check to comfirm if they are hooked up and to the correct wire.

BRAKE LIGHT GREEN (+) @ SWITCH ABOVE BRAKE PEDAL

Last possiblity is a faulty brain (not likely)

http://www.directwholesale.net/diagrams/printpage.asp?ModelID=17326&MakeID=18

Note: You Always Dont Get What You Pay For.

tnez2

Member - Posts: 26

Joined: March 19, 2006

Location: United States

Posted: December 03, 2006 at 1:41 PM / IP Logged

Hi its me , i checked the yellow ign output wire comming from the alarm and it i has 12 volts, is this right?

captainzab

Silver - Posts: 606

Joined: February 09, 2005

Location: United States

Posted: December 03, 2006 at 1:57 PM / IP Logged

20 pin harness

Connect the WHITE/ violet wire (from the autopage) to the BRAKE LIGHT GREEN (+) @ SWITCH ABOVE BRAKE PEDAL

That yellow ignition wire should not have 12v when your car is off.

Note: You Always Dont Get What You Pay For.

tnez2

Member - Posts: 26

Joined: March 19, 2006

Location: United States

Posted: December 03, 2006 at 3:19 PM / IP Logged

I have it connected, but every time i put the fuses back in the heavy guage harness the dash lights up, like it wants to start. i went through every thing again and it looks right.

tnez2

Member - Posts: 26

Joined: March 19, 2006

Location: United States

Posted: December 03, 2006 at 6:02 PM / IP Logged

I cant figure this out. the led stays on and the dash is lit up. so i took it all apart and Im going try to hook it up later. do you all think that the brain is bad. or i wired it wrong. do any of you know any one who hooks up alarms in albquerque new mexico that way i can have a alarm tek put it in for me. please help. thanks

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

autopage 860 wont shut off

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.