92-93 landcruiser wiring diagrams

DIRECTWIRE™ WIRING INFORMATION - TOYOTA / LAND CRUISER / 1993 / Remote Start [PRINT THIS PAGE] 12volts black - WHITE/ red    +   ignition harness Starter BLACK/ white    +   ignition harness Second Starter           Ignition BLACK / YELLOW    +   ignition harness Second Ignition blk/grn or blk/red    +   ignition harness Third Ignition           Accessory blue/red    +   ignition harness Second Accessory           Keysense           Power Lock blue/black    -   driver door harness in kick Power Unlock blu/yel & blu/org    -   driver door harness in kick Notes: Both wires must be used and diode isolated. Lock Motor           Unlock Motor           Parking Lights+ green      drivers kick Parking Lights- RED / black      steering column Hazards           Turn Signal(L)           Turn Signal(R)           Reverse Light           Door Trigger RED / yellow    -   back of cluster Notes: May also be found RED / blue or white in top of the fuse box in a harness from domelight. Use RED / blue for dome supervision. Dome Supervision           Trunk/Hatch Pin tied with door        Hood Pin           Trunk/Hatch Release           Power Sliding Door           Factory Alarm Arm           Factory Alarm Disarm           Disarm No Unlock           Tachometer black    ac igniter or check conn Notes: Check connector is on the passenger side firewall near wiper motor. Igniter is by brake master cylinder. Wait to start           Brake Wire GREEN / WHITE    +   brake switch Parking Brake           Horn Trigger GREEN/ blue    -   steering column Memory Seat 1           Memory Seat 2           Memory Seat 3           Immobilizer Bypass Module: Required: No Type: N/A Part #: N/A Notes: N/A        This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter. Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information. DIRECTWIRE™ WIRING INFORMATION - TOYOTA / LAND CRUISER / 1992 / Remote Start [PRINT THIS PAGE] 12volts black - WHITE/ red    +   ignition harness Starter BLACK/ white    +   ignition harness Second Starter           Ignition BLACK / YELLOW    +   ignition harness Second Ignition blk/grn or blk/red    +   ignition harness Third Ignition           Accessory blue/red    +   ignition harness Second Accessory           Keysense           Power Lock blue/black    -   driver door harness in kick Power Unlock blu/yel & blu/org    -   driver door harness in kick Notes: Both wires must be used and diode isolated. Lock Motor           Unlock Motor           Parking Lights+ green      drivers kick Parking Lights- RED / black      steering column Hazards           Turn Signal(L)           Turn Signal(R)           Reverse Light           Door Trigger RED / yellow    -   back of cluster Notes: May also be found RED / blue or white in top of the fuse box in a harness from domelight. Use RED / blue for dome supervision. Dome Supervision           Trunk/Hatch Pin tied with door        Hood Pin           Trunk/Hatch Release           Power Sliding Door           Factory Alarm Arm           Factory Alarm Disarm           Disarm No Unlock           Tachometer black    ac igniter or check conn Notes: Check connector is on the passenger side firewall near wiper motor. Igniter is by brake master cylinder. Wait to start           Brake Wire GREEN / WHITE    +   brake switch Parking Brake           Horn Trigger GREEN/ blue    -   steering column Memory Seat 1           Memory Seat 2           Memory Seat 3           Immobilizer Bypass Module: Required: No Type: N/A Part #: N/A Notes: N/A        This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter. Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information. Be careful whose advice you buy, but be patient with those who supply it.