Vehicle 2006 Chevrolet Equinox W/ Pioneer Radio Upgrade
Installed Kenwood DVD
ASWC AXXESS
RAP Adapter
Listed in case there are any conflicts. Radio and all features functioning.
Viper 5704
Xpresskit DBALL
flashed with 401.gm5_1.06.01 using Xloader 2 (XPRESS VIP3 Program)
Install Type 6
Would Like to use d2d for the additional features over w2w listed in the features menu.
DBALL Connections
purple / YELLOW to diagnostic connector pin2
BLACK/ white to driver door trigger grey/black
GREEN/ black not used for passlock1
violet/green yellow wire @ ignition
violet/brown yellow wire @ ignition
pink(+)ignition input to Viper Pink 200ma Ignition 1 Output H2/10
In the forum, there are notes to hook this directly in line with the Pink ignition harness?
Viper 5704
Main Harness 6 pin Connector
H1/1 Red (+)12 vdc constant input Battery constant
/2 Black(-) chasis ground ground to chasis
/3 Brown Siren Output(+) (+)Red Siren
/4 WHITE/ Brown Parking Light Isolation Wire Not Used
/5 White Parking Light {fuse polarity (-)} BCM Grey B3 Lt Blue
/6 Orange GWA Output Not Used
Door Lock 3 Pin Connector
1Blue D2D
2 Empty
3Green D2D
Remote Start 10Pin Heavy Gauge Conector
H3/1 Pink Ignition Output Pink Ignition Switch Pin F
/2 RED / White(+) Fused 30A Ignition 2/ Flex Relay Ign Switch Pin A
/3 Orange(+) Accessory Output Ign Switch Orange Wire
/4 Violet Not Used
/5 Green Not Used
/6 Red Not Used
/7 Pink/White (+) Ignition 2/Flex Relay Out Brown
(set as accessory 2 in Menu 3 Remote Start)
/8 Pink/Black Not Used
/9 RED / Black(+) fused (30A) Accessory Not Used
/10 No Connection
Auxillary/ Shutdown/ Trigger Harness
H2/1 Pink/White Not Used
/2 BLACK/ White ground to chasis
/3 Blue/White Second Status D2D
/4 GREEN/ Black OEM Alarm Disarm D2D
/5 RED / White Trunk Release Output N/A
/6 Green (-) Door Trigger Input D2D
/7 BLACK / YELLOW Dome Supervision BCMPink B1 White
/8 BROWN / Black Horn Honk Output BCMPink A3
/9 Dark Blue (-) 200MA status out ???
/10 Pink Wired to D2D
/11 WHITE/ Black (-)200MA Aux3 Out N/A
/12 Violet(+) Door Trigger Input D2D
/13 WHITE/ Violet 200MA Aux 1 Output D2D
/14 Violet/Black 200MA Aux 2 Output N/A
/15 ORANGE / Black 200MA Aux 4 Output N/A
/16 Brown(+) Brake Shutdown (+) LT Blue Brake Pedal
/17 Grey Hood Pin Input N/A
/18 Violet / YELLOW 200MA Starter Out N/A
/19 Blue Trunk Pin/ Instant Trigger D2D
/20 Grey/Black Diesel Wait To Start N/A
/21 WHITE/ Blue RemoteStart/TurboTimer N/A
/22 Orange 200MA Accessory Input N/A
/23 Violet/White Tach Input D2D (tach in menu 3 settings)
/24 (-)200MA oem Alarm Arm Output D2D
The Problem I am experiencing is related to the Pink/White Ignition 2 Flex Relay Output set as accessory.
When connected it is setting off my passlock2 alarm. Ignition will not start car. DBALL will not program, etc.
Disconnect and the programming functions for DBALL, car starts as if alarm is not there. All alarm functions working.
Just not remote start. Alarm brain defective?
Great website! I have used it for massive amounts of information, but am hoping for a little assistane from folks a lot
brighter than myself. From reading the thousands of posts I read before ordering the parts, mapping out the install, etc.
A few members shine brighter than others.
Thanks again if anyone has any thoughts.