Trying to install a remote starter/alarm on my 2000 Explorer. I have a Code Alarm CA-670. If anyone out there can tell me where these wires go, I would be greatful. This is the third one I have put in (94 Explorer, and a 1999 F150), but I seem to be having trouble with this one. Have some wires connected, but cannot get the Explorer to remote start, nor get the alarm to work (I guess I need all of them connected to get it to work?).
22 Pin Harness
BLACK/ WHITE DOME LIGHT OUTPUT (Connected BLACK/ LT Blue dr. side kick panel)
Lt BLUE/RED MANUAL ARM INPUT this goes to?
Lt BLUE/GREEN BLUE UNLOCK SENSE INPUT this goes to?
BLUE/WHITE INSTANT TRIGGER INPUT (-) this goes to?
WHITE/ BLUE REMOTE START ACTIVATION (-) this goes to?
GREEN NEGATIVE DOOR TRIGGER this goes to?
WHITE PARKING LIGHT OUTPUT (Connected to brown wire at switch)
PINK CHANNEL 1 (TRUNK) this goes to?
Lt BLUE/BLACK MANUAL DISARM INPUT this goes to?
PURPLE POSITIVE DOOR TRIGGER I believe this goes to the dome light connection?
Lt GREEN/ ORANGE HEADLIGHT OUTPUT (-) (Relay installed, is it needed?)
BROWN / BLACK HORN OUTPUT (-) (Connected Lt. YELLOW /GREEN)
PURPLE / WHITE TACH INPUT (Connected at PCM Tan / YELLOW wire)
ORANGE ARMED OUTPUT (-) this goes to?
4 Pin Harness
PINK (+) IGNITION 1 INPUT/OUTPUT this goes to?
RED (+) 12 VOLTS BATTERY (Connected to yellow wire at ignition switch harness)
GREEN (+) STARTER INPUT(KEY SIDE)(Connected to key side of RED / light blue wire at ignition switch harness)
PURPLE (+) STARTER OUTPUT(MOTOR SIDE)(Connected to starter side of RED / light blue wire at ignition switch harness)
6 Pin Harness
RED (+)12 VOLTS BATTERY (Connected to yellow wire at ignition switch harness)
ORANGE (+) ACCESSORY 1 OUTPUT this goes to?
ORANGE / WHITE (+) ACCESSORY 2 OUTPUT this goes to?
PINK/WHITE (+) IGNITION 2 OUTPUT this goes to?
BROWN / RED (+) BRAKE INPUT (Connected Lt. Green wire at brake switch)
BLUE/BLACK (-) ACTIVE OUTPUT this goes to?
I have the PKF1 Module
Are the doors negative or reverse polarity (factory keyless)? Out of the control module I have:
BLUE/GREEN (-) 2ND STAGE UNLOCK
BLUE NEGATIVE UNLOCK/POSITIVE LOCK
GREEN NEGATIVE LOCK/POSITIVE UNLOCK
How do I wire the locks? On the 1994 Explorer I used a 451m Micro Doorlock Module, I have one of these, but I cannot remember how to hook this up.
If there is any other info I need, please feel free to let me know.
Thanks for your help in advance,
Ted
2000 Ford Explorer Alarm, Remote Starter, Keyless Entry Wiring Information
Constant 12V+ Yellow Ignition Switch Harness
Starter RED / Light Blue Ignition Switch Harness
Ignition Light GREEN/ Purple Ignition Switch Harness
Ignition 2 Gray / YELLOW Ignition Switch Harness
Ignition 3 BLACK/ Green Ignition Switch Harness
Accessory Gray / YELLOW Ignition Switch Harness
Tach Tan / YELLOW Coil or Pin 48 at PCM
Neutral Safety Wire RED / Light Blue (+)
Brake Switch Light Green Brake Switch
Trunk Pin n/a Common with Doors
Parking Lights WHITE/ Black (+) Or Brown at Switch or Driver's Kick Panel
Head Lamp RED / Yellow (+) Light Switch
Hood Pin Tan/Light Green (-) Driver's Kick Panel
Factory Disarm Dark GREEN/ Purple (-) 4 Pin Connector Driver's Kick Panel
Door Trigger BLACK/ Light Blue (+) Courtesy Light under Dash
Door Lock Pink / YELLOW (-) Driver's Kick Panel
Door Unlock Pink/Light Green (-) Driver's Kick Panel
Driver's Lock Pink/Black (+) Driver's Door Harness
Driver's Unlock RED / Orange (+) Driver's Door Harness
Passenger Unlock Pink/Green (-) Driver's Kick Panel
Horn Wire Yellow/Light Green (-) Or Blue at Steering Column
Windows Up LF=WHITE/ Black, RF=Tan/Light Blue, LR=Gray/Orange, RR=Yellow/Black
Windows Down LF=Red, RF=WHITE/ Yellow, LR=Yellow/Light Blue, RR=RED / Black