the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

calculating resistor size


Post ReplyPost New Topic
< Prev Topic Next Topic >
bluburd 
Member - Posts: 19
Member spacespace
Joined: February 20, 2006
Location: United States
Posted: February 12, 2009 at 3:32 PM / IP Logged  

Hey everyone,

I have the following LEDs and are trying to figure out what size resistor I need. I am wiring them in parallel from my vehicle (12 volts).

a.)  12,000 mcd, 1.8-2.2 volts, 24mA

b.) 5,000 mcd, 1.8-2.2 volts, 24mA

Do I assume 12 volts when calculating since the car really operates at 9-14 volts?  Also, should I use the 1.8 or 2.2 when making the calcualation?

If anyone can help answer my questions and give me their opinion on what size resistors I'll need, I'd appreciate it.

Thanks.

bluburd 
Member - Posts: 19
Member spacespace
Joined: February 20, 2006
Location: United States
Posted: February 12, 2009 at 3:59 PM / IP Logged  
I also wanted to mention that I don't necessarily need to get all of the brightness out of the LEDs. If I can run a different resistor and have them a little dimmer, that's fine too.
i am an idiot 
Platinum - Posts: 13,693
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: February 12, 2009 at 5:20 PM / IP Logged  

Just to be safe, a 1000 ohm resistor will safely light up any LED I have run across.  I have never seen any damage done by using a 470 ohm either.

ckeeler 
Gold - Posts: 1,461
Gold spacespace
Joined: June 20, 2008
Location: New Mexico, United States
Posted: February 12, 2009 at 7:25 PM / IP Logged  
depends alot on the LED but i normally use 470. i use 1000 too but i also notice i can always use a 470 on the same resistor and its a little bit brighter.
91stt 
Silver - Posts: 564
Silver spaceThis member consistently provides reliable informationspace
Joined: May 24, 2006
Location: New Jersey, United States
Posted: February 12, 2009 at 9:39 PM / IP Logged  
Since both LED's have similar specs it makes it much easier. Use 2V as a reference for each LED.
Assuming a nominal voltage of 12V from the battery, the voltage drop across the resistor should be 10V. Using Ohm's law, R=E/I. R = 10/0.024 = 417 ohms. The closest standard resistor is 430 ohms.
With a nominal battery voltage of 14V, voltage drop across the resistor should be 12V, so R = 12/0.024 = 500 ohms and the closest standard resistor is 510 ohms.
Depending how safe you want to be, you can a resistor is small as 430 ohms. A higher resistance would result in less brightness.
If you decide to wire the LED's in parallel, you only need one resistor.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer