the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

DEH-p3500. wiring harness fell apart


Post ReplyPost New Topic
< Prev Topic Next Topic >
rhunt 
Member - Posts: 3
Member spacespace
Joined: January 02, 2006
Location: United States
Posted: February 22, 2006 at 2:52 AM / IP Logged  

I was taking out my Pioneer DEH-P3500 of my 86 Nissan truck to put it in my just bought 2004 Nissan Xterra. I guess as I was getting it out  (which I did as carefully as possible), some of the wires on the harness that came with the Pioneer came out. and I don't want to mix them up and short anything or have to redo anything. The wires that came out are both green and green w/black stripe and gray/gray w/ black stripe which I know are speakers. Also the solid yellow, and the black ground wire. I have looked at hanesses for sale online and I cannot tell what goes where by the pictures. Could somebody please let me know what pin holes they are placed in. I know that another wire harness is cheap but after buying this Xterra that cheap harness is still to much for me to pay.

Any help would be much appreciated,

Thanks Rhunt

jahnkematthew 
Member - Posts: 19
Member spacespace
Joined: February 20, 2006
Location: Canada
Posted: February 22, 2006 at 7:34 PM / IP Logged  

the first top left pin is for the BLACK ground...the first bottom left pin hole is yellow... the 2nd pin hole from the top left is red..the first and 2nd pin from the top RIGHT are purple....beside the purple on the top, the next two pin holes are green...bottom right (below purple) the first two pin holes are grey....beside grey on the bottom right are white...thats it for my pioneer

hope thats what u were asking for...

matt

i would like to know how u took the deck out......hahaha

jahnkematthew 
Member - Posts: 19
Member spacespace
Joined: February 20, 2006
Location: Canada
Posted: February 22, 2006 at 7:37 PM / IP Logged  

and the lefts and rights are as if the clip that holds the harness in the deck is facing UP

matt

rhunt 
Member - Posts: 3
Member spacespace
Joined: January 02, 2006
Location: United States
Posted: February 24, 2006 at 7:37 PM / IP Logged  

Man, thanks so much works great thanks to you.

thanks again, rhunt

rhunt 
Member - Posts: 3
Member spacespace
Joined: January 02, 2006
Location: United States
Posted: February 24, 2006 at 7:44 PM / IP Logged  

As for how I had taken the deck out. I swear I did it as careful as possible. But since I have had the truck I have had a few decks in there and the factory wires have been getting shorter and shorter so it is barely enough room to undo the harness which it kinda pinched my hand which kinda pissed me off. That is when I may have jerked on it a little to hard but still I did it as careful as possile.

Thanks again


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer